madkaw Posted August 13, 2019 Share #2701 Posted August 13, 2019 Build is looking good. Too late now but I would have mentioned that you could shove 14mm high impedance injectors in the stock manifold and they will seal. Probably a mute point if have a 11mm fuel rail. I’m running Audi 1.8 Bosch type now. As far as catch can , PCV, etc, I added a pic of mine . You said you run a catch can, probably plumbed the same way. There’s a few hoses there if you can pick it out. The hose off the intake is for the IAC . The can catches more than I thought. I like how you cleaned the intake up. I need to do a cable myself to get rid of the linkage. 1 Link to comment Share on other sites More sharing options...
wheee! Posted August 13, 2019 Author Share #2702 Posted August 13, 2019 TPS sensor plate came in today too! Link to comment Share on other sites More sharing options...
madkaw Posted August 13, 2019 Share #2703 Posted August 13, 2019 I was ready to go that route when I thought I was having issues with my TPS . Looks like a cool set up Link to comment Share on other sites More sharing options...
wheee! Posted August 13, 2019 Author Share #2704 Posted August 13, 2019 10 hours ago, madkaw said: I was ready to go that route when I thought I was having issues with my TPS . Looks like a cool set up The Haltech is so configurable and definable for inputs that it leaves me with these great opportunities to tune and refine the entire combustion process! I am really excited to get all the sensors installed and reporting to the ECU in order to max out the potential of this motor. Good news is, a certain influential someone who sold me this motor just got HIS Haltech system working with a similar setup, so that is very encouraging!! 1 Link to comment Share on other sites More sharing options...
madkaw Posted August 13, 2019 Share #2705 Posted August 13, 2019 Haltech should be great. What MAP sensor are you going to run and where are you installing it? Link to comment Share on other sites More sharing options...
Patcon Posted August 13, 2019 Share #2706 Posted August 13, 2019 2 hours ago, wheee! said: The Haltech is so configurable and definable for inputs that it leaves me with these great opportunities to tune and refine the entire combustion process! I am really excited to get all the sensors installed and reporting to the ECU in order to max out the potential of this motor. Good news is, a certain influential someone who sold me this motor just got HIS Haltech system working with a similar setup, so that is very encouraging!! Is that on the 510? Link to comment Share on other sites More sharing options...
madkaw Posted August 13, 2019 Share #2707 Posted August 13, 2019 2 hours ago, wheee! said: The Haltech is so configurable and definable for inputs that it leaves me with these great opportunities to tune and refine the entire combustion process! I am really excited to get all the sensors installed and reporting to the ECU in order to max out the potential of this motor. Good news is, a certain influential someone who sold me this motor just got HIS Haltech system working with a similar setup, so that is very encouraging!! It has been fun for me to play with all the numbers . With complete control you can run a ton of advance and run the motor lean without worrying . Cruise at 16AFR and 45 degrees all day . The beauty of having a well engineered mechanical platform and modern technology to run it 1 Link to comment Share on other sites More sharing options...
wheee! Posted August 13, 2019 Author Share #2708 Posted August 13, 2019 1 hour ago, madkaw said: Haltech should be great. What MAP sensor are you going to run and where are you installing it? The Haltech Elite750 has a built in sensor for MAP that runs off a vacuum line from the manifold direct to the ECU 1 hour ago, Patcon said: Is that on the 510? *bingo! Link to comment Share on other sites More sharing options...
wheee! Posted August 13, 2019 Author Share #2709 Posted August 13, 2019 I also added a fuel pressure monitoring circuit to the return fuel line on the recommendation of my Z Car Club. The Haltech can monitor the pressure and shut down the timing if the fuel pressure drops below a preset. Cool! This along with two liquid pressure gauges in the engine bay should keep me well informed. 1 Link to comment Share on other sites More sharing options...
madkaw Posted August 13, 2019 Share #2710 Posted August 13, 2019 41 minutes ago, wheee! said: I also added a fuel pressure monitoring circuit to the return fuel line on the recommendation of my Z Car Club. The Haltech can monitor the pressure and shut down the timing if the fuel pressure drops below a preset. Cool! This along with two liquid pressure gauges in the engine bay should keep me well informed. Fancy! Beware condensation in the MAP sensor line will roll down hill right into the ecu and kill the sensor . I had to go external . Unless you can use a newer style that uses no hose to the ecu Link to comment Share on other sites More sharing options...
wheee! Posted August 13, 2019 Author Share #2711 Posted August 13, 2019 12 minutes ago, madkaw said: Fancy! Beware condensation in the MAP sensor line will roll down hill right into the ecu and kill the sensor . I had to go external . Unless you can use a newer style that uses no hose to the ecu I will route my vacuum hose in a manner to avoid that. Thanks! Link to comment Share on other sites More sharing options...
madkaw Posted August 13, 2019 Share #2712 Posted August 13, 2019 Pretty sure you will need an additional sensor for sequential . That one wheel can’t do it all . Maybe you misunderstood them. Still- I’m only running wasted spark and it’s still light years ahead of a dizzy Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now