New bushings - car seems to slide back & forth - bumps, shifting

[Redwing]

I had a local mechanic put in new bushings all around. When finished, car makes a thumping noise. She seems to feel loose and rattle back and forth when shifting, going over bumps, and foot off gas and replaced. The mechanic says it is nothing they did. Could it be they did not tighten everything back? Any ideas what it could be?

Thank you.

[rcb280z]

Check your differential mount.

[Redwing]

Does that have any connection with the rear bushings? They were to put in struts too, but the people who prepared it for sale had already put new struts in. So they went in there, but did not put more struts in.

Thank you

[Zed Head]

I had a local mechanic put in new bushings all around. 

Do you have a list of what was replaced, and what they were replaced with?  Factory bushings or aftermarket?

 

There are a lot of bushings on the car.  

 

And, why did you have the bushings replaced?  Is the car worse, the same, or better but still not good, now?

Edited June 20, 2015 by Zed Head

[siteunseen]

Check your differential mount.

The word "thump" is what got that reply.  They're notorious for that noise when shifting gears when the differential mount is worn.

[HaZmatt]

Check the strut mounts up top, they might be loose. This reminds me of a time when I took my 4runner in for service because of some random "thumps". I told them " i think its the u joints in the driveshaft", they ended up replacing the rack and pinion instead. It was way worse when I picked it up. All the bolts were loose and some were missing. It ended up being the U joints. 

[Montana Z]

Just got finished fixing a similar problem on my car.  In my case to was loose rear inner control arm bolts/ bushings.  Not too hard to check on your own.  It takes a 24mm wrench.  The torque is supposed to be 115 ft/lbs.

Edited June 20, 2015 by Montana Z

[Redwing]

The noise seems to be coming from the back inside of car, the left rear strut to be exact.

[Redwing]

I think these are the bushings. They were replaced because the old ones were crumbling.

On ebay, item number 4100580223239 A whole box of them.

Energy Suspension Polyurethane Hyper-Flex System

1974-1978 Nissan Datsun 260Z 280Z

Energy Part # 7.18102R

Hyper Flex Kit Includes:

Front Control Arm Bushings

Rear Control Arm Bushings

Front Strut Rod Bushings

Front Bump Stops

Rear Bump Stops

Rack and Pinion Bushings

Differential Carrier Mustache Bar Bushings

Front End Links

Tie Rod End Boots

Transmission Crossmember Bushings

Rear Sway Bar Bushings

Rear End Link Bushings

[siteunseen]

Putting the whole box of bushings on your car would be thousand dollar job to me. It's a lot of work. Some I couldn't get to until I pulled the motor. The rear control arm bushings are still left over in the box. But you're an honest lady so I'd charge you less. Smiley face emoticon.

Read the tech tips under SUSPENSION. You'll see the hyper flex install. In red like yours.

Edited June 20, 2015 by siteunseen

[Patcon]

If they put in a whole poly bushing kit, the car shouldn't be any looser. Could be a little noisier as the poly bushing are firmer and transmit more sound.

[grannyknot]

I had similar sounds coming from the back and it took me weeks to track it down, it turned out that one of the gland nuts that hold the shock absorber secure in the strut tube had worked itself lose and the shock was banging around with every little bump in the road.

Chris