hiyabrad Posted November 6, 2018 Share #277 Posted November 6, 2018 2 minutes ago, duffymahoney said: I have stock style wire ones. I am waiting on a L fuel fitting from Japan. Then I swill swap them all out. Can you elaborate on the "L" fuel fitting? Why are you using it? Do you have a pic of what it looks like you can post? And where are you getting it from? I am going to build a similar set up and would love to know the details. Thanks! Link to comment Share on other sites More sharing options...
duffymahoney Posted November 7, 2018 Author Share #278 Posted November 7, 2018 You can see one L and 2 Ts on my carbs. One of the T’s has a called end. 1 L i have now is a left. I need a right facing one. They are a little harder to find. Link to comment Share on other sites More sharing options...
hiyabrad Posted November 7, 2018 Share #279 Posted November 7, 2018 16 minutes ago, duffymahoney said: You can see one L and 2 Ts on my carbs. One of the T’s has a called end. 1 L i have now is a left. I need a right facing one. They are a little harder to find. I guess I have the same issue then. Any leads on finding a right facing "L"? Thanks Link to comment Share on other sites More sharing options...
duffymahoney Posted November 7, 2018 Author Share #280 Posted November 7, 2018 Most people run the fuel just like you have it setup there. I just decided to go different. Link to comment Share on other sites More sharing options...
Patcon Posted November 8, 2018 Share #281 Posted November 8, 2018 So I assume the fitting is not reversible for some reason? Link to comment Share on other sites More sharing options...
duffymahoney Posted November 9, 2018 Author Share #282 Posted November 9, 2018 4 hours ago, Patcon said: So I assume the fitting is not reversible for some reason? It’s designed to go one way. It holds the fuel filter in and has a inside flange. Link to comment Share on other sites More sharing options...
Patcon Posted November 9, 2018 Share #283 Posted November 9, 2018 11 hours ago, duffymahoney said: It’s designed to go one way. It holds the fuel filter in and has a inside flange. ok, that makes sense I did a little looking. Looks like it might be a hard find. You might could rework one. Under the plating the tube is soldered or brazed in. Heat it and reverse it and have it replated. Not a very cheap way to do it, but it should get you to where you want to be 1 Link to comment Share on other sites More sharing options...
duffymahoney Posted November 12, 2018 Author Share #284 Posted November 12, 2018 Finally found some series 1 wheel chocks. I sent off for around 30 yellow powder samples. I decided on 02 VETTE YELLOW by Prismatic powders. It was close, just slightly brighter, I think when new this would have been almost identical. First picture was taken indoors under terrible lighting. This finishes off my series 1 tool kit. 2 Link to comment Share on other sites More sharing options...
duffymahoney Posted November 13, 2018 Author Share #285 Posted November 13, 2018 I believe this is installed correctly. Anyone? Link to comment Share on other sites More sharing options...
jfa.series1 Posted November 13, 2018 Share #286 Posted November 13, 2018 Spot on!!! Looking great, congrats. Link to comment Share on other sites More sharing options...
duffymahoney Posted December 5, 2018 Author Share #287 Posted December 5, 2018 Ok, now onto my horns. I always hated how they look. Poor repray covering them. Interesting that the front of the horns looked to have been the dark green zinc. Then sometimes from the factory with some over spray. Same zinc as the seat sliders. ZedSaver does gold zinc. I am a little torn on what to do. Also how to take this fully apart to zinc? You can see in the blue z picture the green really showing through. Link to comment Share on other sites More sharing options...
duffymahoney Posted December 7, 2018 Author Share #288 Posted December 7, 2018 (edited) I finally got the correct fuel fitting from japan to finish my old school looking fuel rail. I love how it turned out! I had to have it re - zinc’d since the Mikuni and my plater color didn’t match. Edited December 7, 2018 by duffymahoney 3 Link to comment Share on other sites More sharing options...
Yarb
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now