Zed Head Posted May 2, 2019 Share #361 Posted May 2, 2019 Be careful. I see a socket lurking... 1 Link to comment Share on other sites More sharing options...
duffymahoney Posted May 2, 2019 Author Share #362 Posted May 2, 2019 it's probably a 10mm:) Link to comment Share on other sites More sharing options...
duffymahoney Posted May 3, 2019 Author Share #363 Posted May 3, 2019 Nos 240z starter solenoid score. eBay 9$ shipped! Time to rebuild the starter. Link to comment Share on other sites More sharing options...
Mike Posted May 3, 2019 Share #364 Posted May 3, 2019 On 4/29/2019 at 5:55 PM, duffymahoney said: More stuff back from zinc. Time to install some stuff. Man, that zinc plating looks great!! Link to comment Share on other sites More sharing options...
duffymahoney Posted May 3, 2019 Author Share #365 Posted May 3, 2019 I wanted to send it back, since it was so blue/ purple, I decided to just live with it. Link to comment Share on other sites More sharing options...
Patcon Posted May 4, 2019 Share #366 Posted May 4, 2019 16 hours ago, duffymahoney said: I wanted to send it back, since it was so blue/ purple, I decided to just live with it. Did you contact them at all? Link to comment Share on other sites More sharing options...
Popular Post duffymahoney Posted May 4, 2019 Author Popular Post Share #367 Posted May 4, 2019 (edited) Well shimming the r-180, backlash, pre load and wipe pattern took most of a couple days after work and most of a Saturday morning. I think I took it apart 20+ times. Finally happy with the wipe pattern. Luckily I didn’t have to change the pinion shim. Edit: I think in a perfect world I would have had a special tool to set the pinion nut at the factory 125-150ftlb. Then used different shims to get the bearing pre load perfect. But I had no way, so a couple of hits with the impact is what I used to set pre load, I found that info on here and a few youtube videos. It's not precise at all, just hopeful the factory had it correct enough. A bunch of site posts and a few guru told me to just reuse the pinion shim and move on. Everyone basically told me backlash is the most important. Ended up with 5 thousandths for backlash give or take and then ring side backlash shim if .05 and other side of .07. Total inch pounds is around 8-10 on the pinion. No carrier I had around 3 inch pounds for the pinion. This is worth paying someone to do. Just FYI. I had fun. But super frustrating. Edited May 5, 2019 by duffymahoney 5 Link to comment Share on other sites More sharing options...
duffymahoney Posted May 5, 2019 Author Share #368 Posted May 5, 2019 She is in. Gosh I hope it works nicely and I didn’t screw up! I really like how the half shafts hades turned out. 1 Link to comment Share on other sites More sharing options...
duffymahoney Posted May 5, 2019 Author Share #369 Posted May 5, 2019 Osgiken clutch is in. Big thanks to Zgarage for the kit. Install was a breeze. 1 Link to comment Share on other sites More sharing options...
duffymahoney Posted May 15, 2019 Author Share #370 Posted May 15, 2019 I got the starter put back together. Hopefully it works! Sure looks nicer. 2 Link to comment Share on other sites More sharing options...
duffymahoney Posted May 15, 2019 Author Share #371 Posted May 15, 2019 Finally got the ka trans. This is a low mileage (500) miles trans. Been sitting on the shelf since 1989. I found it on some parts website. Vapor and some zinc and it’s looking amazing. Bell housing mods are being done Emerish racing. 2 Link to comment Share on other sites More sharing options...
Patcon Posted May 15, 2019 Share #372 Posted May 15, 2019 The bracing flanges on that case look amazing! Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now