duffymahoney Posted August 16, 2019 Author Share #445 Posted August 16, 2019 Plug clears with ease Link to comment Share on other sites More sharing options...
duffymahoney Posted August 16, 2019 Author Share #446 Posted August 16, 2019 I love how the harness will tuck 1 Link to comment Share on other sites More sharing options...
wheee! Posted August 16, 2019 Share #447 Posted August 16, 2019 Oh, now that is nice! Looking forward to seeing this complete! Link to comment Share on other sites More sharing options...
duffymahoney Posted August 20, 2019 Author Share #448 Posted August 20, 2019 I got all my boots in, I wish there was an easy way to test the coils. But I know the spring is compressed on the spark plug, so I should be good. How has everyone run new ecu wiring into the engine bay? My early 240z has dealer AC. Which complicates things. Really I only have two holes open. The choke cable hole and the tunnel hole near the shifter. I would rather not cut any holes. If I leave the coil power wiring in the engine bay and do the o2 sensor and maybe the triggers for the coils through tunnel hole I am thinking I might have enough room for it with those two holes? It’s going to be tight, but I think I can do it all clean and nice. I will be using german braied loom for the whole project. No pulsed outputs. Plans Choke hole Injector wiring Cas wiring Air temp Coolant temp TPS Crank trigger wiring Tunnel hole Injector triggers Power and ground O2 sensor Fuel pump wiring is already in place. I also got in the euro kit from Hoke for my crank trigger. Which should work better on my series 1 dampener. I have to remove .08 from the backside to have it perfect. Then off to paint. Blue or black?! 1 Link to comment Share on other sites More sharing options...
wheee! Posted August 20, 2019 Share #449 Posted August 20, 2019 The 280Z has a lot more options for wiring as there is the original FI hole on the drivers side plus the standard wiring harness hole on the passenger side. Link to comment Share on other sites More sharing options...
madkaw Posted August 20, 2019 Share #450 Posted August 20, 2019 I used my AC holes since I don’t have AC. Where are you mounting the ECU? I split up my harness running my sensor wires out the opposite side of the engine using the choke hole. Link to comment Share on other sites More sharing options...
wheee! Posted August 20, 2019 Share #451 Posted August 20, 2019 15 minutes ago, madkaw said: I used my AC holes since I don’t have AC. Where are you mounting the ECU? I split up my harness running my sensor wires out the opposite side of the engine using the choke hole. I haven't decided yet. I have the original ECU location behind the panel on the drivers side footwell, but I also want easy access for the USB port for programming. I actually have a plan to run a USB extension into the dash for the Haltech programming. I also have the CANBUS kit that needs to be installed as well for the wideband O2 sensor. Link to comment Share on other sites More sharing options...
duffymahoney Posted August 20, 2019 Author Share #452 Posted August 20, 2019 I will do the canbus wideband as well. I will do the passenger kick panel install. Datsun spirit sales a plate that bolts in. Link to comment Share on other sites More sharing options...
madkaw Posted August 20, 2019 Share #453 Posted August 20, 2019 I mounted my MS3 on the trans tunnel on passenger side . Since I decided to run my harness thru the AC holes I figured I would keep the ECU closer to that . Not sure there is a right or wrong for location- it depends on the owners set up. Link to comment Share on other sites More sharing options...
duffymahoney Posted August 22, 2019 Author Share #454 Posted August 22, 2019 Working on my 280zxt Cas signal, so I can do full sequential. I got a very nice 280zxt distributor without a cas from a fellow Datsun nerd. I then found a basically new fully Nissan Cas from a 1998 Nissan Quest. Which has the correct trigger wheel. Pretty neat. Dizzy is getting vapor blasted today and I should have it all installed by the weekend. Pretty excited! 2 Link to comment Share on other sites More sharing options...
duffymahoney Posted August 27, 2019 Author Share #455 Posted August 27, 2019 280zxt dizzy is done. I vapor blasted it the housing, wrinkle coated the godzilla race works cap and new zinc hardware. I might not be able to live with the size of it. It's pretty huge. 2 Link to comment Share on other sites More sharing options...
madkaw Posted August 29, 2019 Share #456 Posted August 29, 2019 Have you seen the thread on Hybridz using the Jeep cam angle sensor ? Link to comment Share on other sites More sharing options...
Parman
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now