Namerow Posted September 3, 2020 Share #25 Posted September 3, 2020 The Loctite brand used to offer a product specifically for repairing rear window defrost grids. Came in a small glass bottle with a little applicator brush built into the cap. 1 Link to comment Share on other sites More sharing options...
Dave WM Posted September 3, 2020 Author Share #26 Posted September 3, 2020 8 hours ago, ensys said: Just a couple thoughts... I think perhaps there is a good reason that all the old manuals illustrate repairs being done with an old fashion drafting pen (looks like the long bill of a bird). The advantage is that (theoretically) one doesn't have to mask (the bill or "nib" is adjustable for width, and when used properly, will produce a very clean edge. the other positive is that the bead will have a slightly rounded top that would provide more net cross section. The other is that isn't such a grid usually coated with a thin, clear protective layer of something? Or not. the issue is I have lost prob more than 50% of the grid, so its more of a restoration process than a repair. the grid literally appears to have faded away. I don't know about any coating, but I doubt it since that would make even a repair difficult. there are kits that have stick on grids, but I really did not like the idea of that. Maybe they work but seems like that would have its own set of issues. I rarely use the defogger mode, but sometimes with high humidity and my AC on high it does fog up from the outside. Link to comment Share on other sites More sharing options...
Zed Head Posted September 3, 2020 Share #27 Posted September 3, 2020 I bought a defrost fan from OReilly, replaced the cigarette lighter terminal with two spade connectors and connected it to the power circuit for the grid. It was kind of noisy but it worked. The grid is better of course but if you want something to use in the meantime, the fan's only about $20. The defrost grid is on a 20 amp circuit, so lots of juice there. https://www.oreillyauto.com/detail/b/custom-accessories-3126/accessories-16449/winter-accessories-16523/defroster-defogger-23801/5aa88c03919b/custom-accessories-defroster/48701/5981244 Link to comment Share on other sites More sharing options...
dutchzcarguy Posted September 4, 2020 Share #28 Posted September 4, 2020 Just wanted to ad.. i had 5! rear windows for my 280zx and i installed the one with the lowest ohms.. it was if i remember correctly around 2,2-2,4 ohms.. (incl. 0.2 ohms for leads) The one i installed worked on every line! so i think the total resistance of your 240z def.grid should be around 2-2.5 ohms.. Long ago i used some bison silverglue on a grid but did'nt like it.. very difficult to put on and not make a mess haha.. Link to comment Share on other sites More sharing options...
Dave WM Posted September 4, 2020 Author Share #29 Posted September 4, 2020 33 minutes ago, dutchzcarguy said: Just wanted to ad.. i had 5! rear windows for my 280zx and i installed the one with the lowest ohms.. it was if i remember correctly around 2,2-2,4 ohms.. (incl. 0.2 ohms for leads) The one i installed worked on every line! so i think the total resistance of your 240z def.grid should be around 2-2.5 ohms.. Long ago i used some bison silverglue on a grid but did'nt like it.. very difficult to put on and not make a mess haha.. I am hoping the stencil helps, what was the process you used to apply? so far I have tried masking tape and plastic electrical tape applied free hand (masking tape had too much bleed under, electrical tape was better but very hard to get a consistent width). this was on a plain sheet of glass as a test. I also purchased a pin stripe brush hoping it loads better. Link to comment Share on other sites More sharing options...
ensys Posted September 5, 2020 Share #30 Posted September 5, 2020 Might I suggest that given a clean surface to start, plastic Scotch tape has a good edge, and is more stable than elect. tape, making a straight line easier to obtain. Plus, it leaves less adhesive residue than moderne masking tape. Just a thought... Link to comment Share on other sites More sharing options...
Dave WM Posted September 5, 2020 Author Share #31 Posted September 5, 2020 (edited) 15 minutes ago, ensys said: Might I suggest that given a clean surface to start, plastic Scotch tape has a good edge, and is more stable than elect. tape, making a straight line easier to obtain. Plus, it leaves less adhesive residue than moderne masking tape. Just a thought... the plan is to try the purpose made stencil tape, it has provision for a constant 1/16 line once applied then the center is removed. I was not happy with any of the various tape methods as getting the constant width was an issue, esp when considering I have to do the entire grid. The stencil was designed around the idea of quick pin stripe methods not requiring great skill to apply in the automotive industry. Edited September 5, 2020 by Dave WM 2 Link to comment Share on other sites More sharing options...
AK260 Posted September 5, 2020 Share #32 Posted September 5, 2020 Have you considered replacing the entire grid by overlaying with one of these?https://frostfighter.com/clear-view-defrosters-16.htm Link to comment Share on other sites More sharing options...
dutchzcarguy Posted September 5, 2020 Share #33 Posted September 5, 2020 19 hours ago, Dave WM said: what was the process you used to apply? i used a sort of pinstripe brush.. a small brush with long hairs and just a few hair.. did'nt work well. the bison silverglue was very liquid.. never tried masking it. Link to comment Share on other sites More sharing options...
Patcon Posted September 7, 2020 Share #34 Posted September 7, 2020 Do anyone know how the process was originally done? Seems that would help come up with a replacement process @HS30-H Link to comment Share on other sites More sharing options...
Namerow Posted September 7, 2020 Share #35 Posted September 7, 2020 Done with a stencil and a liquid-copper spray would be my guess. Anybody have OEM automotive glass experience? Link to comment Share on other sites More sharing options...
Captain Obvious Posted September 7, 2020 Share #36 Posted September 7, 2020 I would guess they silk screened it. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now