I am trying to find a good replacement for the gas tank drank plug and washer. Does anyone know where to get them? My washer is disintegrated and the bolt has a slow leak and I am not even sure it’s the correct plug.

 

 

Sent from my iPhone using Classic Zcar Club mobile

Pretty pretty pretty sure that somebody out there knows the thread pitch and  size but here's a link to the Nissan part numbers.  They call it a plug and packing.  Talk about translation problems.

http://www.carpartsmanual.com/datsuns30/Datsun-Z-Index/Engine-280Z/Fuel-Tank/From-Jul-76

BIG EDIT Sorry about this but the 1/2"x20 is completely wrong, You are looking for an M8x1.25 bolt.

I was looking through my notes and 1/2"x20 is what I have there but that must be for something else, I just went out to the storage shed to dig out the gas tank. A 1977 280z gas tank has M8x1.25 drain bolt.

Note to self, re check my notes

Edited December 9, 20186 yr by grannyknot

I also found it to be a standard thread and not metric. I found that odd but didn't fight it.

5 minutes ago, Patcon said:

I also found it to be a standard thread and not metric. I found that odd but didn't fight it.

Actually, I'm still trying to find mine, I removed it when I was restoring the tank and put it somewhere safe, so safe it still hasn't shown up, I may have to make one.

6 minutes ago, grannyknot said:

Actually, I'm still trying to find mine, I removed it when I was restoring the tank and put it somewhere safe, so safe it still hasn't shown up, I may have to make one.

Don't you hate it when you do that! I have a roll pin I took out of something. Put it in a conspicuous place in the shop so I wouldn't lose it.

I still have it, but I forgot what it came out of....

Well the plug is still available but it looks like but the “packing” is NLA. what should I use to replace the washer? (Correction both are NLA)

 

Sent from my iPhone using Classic Zcar Club mobile

 

Well this is interesting https://parts.nissanusa.com/nissanparts/index.cfm?action=replacement&siteid=14&jointvehid=18157&groupid=B&sectionid=172&partcode=17201A



Sent from my iPhone using Classic Zcar Club mobile

Well, if the 1/2 x 20 is correct, this would probably work: https://www.amazon.com/Needa-Parts-652036-Drain-Plug/dp/B000CHL58M

Or this: https://www.summitracing.com/parts/sdk-d1az-6730-a/overview/

The part 01125-00062 is also on the 1985 200sx and the “packing” and both are still available. Going to order today and see what I get

 

 

Sent from my iPhone using Classic Zcar Club mobile

 

33 minutes ago, ryanotown22 said:

Well the plug is still available but it looks like but the “packing” is NLA. what should I use to replace the washer? (Correction both are NLA

 

Sent from my iPhone using Classic Zcar Club mobile

 

@ryanotown22, my apologies, see post #3.  Forget the 1/2"x20 that is completely wrong, my notes are wrong. The drainage bolt you are looking for is a M8x1.25,  I just checked my gas tank and it is M8x1.25,  what a twit.

The problem with a standard M8x1.25 is the bottom of the head isn't really flat and there is not much of it to get a crush washer to do its job. The original drain bolt had a larger head with a machined flat bottom for a good seal.

The "packing" is the copper or aluminum crush washer.

Edited December 9, 20186 yr by grannyknot

Ok thanks if the parts I just ordered don’t fit I will just pick that up. Btw my order total price came to 2.18 for the plug and washer from Nissan with local pickup

 

 

Sent from my iPhone using Classic Zcar Club mobile