Namerow Posted March 2, 2019 Share #13 Posted March 2, 2019 I agree with your premise. I know you're busy with the real work right now, but later, when time permits, please consider creating a set of drawings for your jig. It would make a great addition to the restoration resources that this great site makes available to others. BTW, you have a real talent for visualizing sheet metal repairs. The fab part is half of it, but the 'vision' part (i.e 'How do I translate this into cuts and bends and welds) is equally important. 3 Link to comment Share on other sites More sharing options...
ConVerTT Posted March 2, 2019 Author Share #14 Posted March 2, 2019 Thanks Namerow! Good idea - my “notes” are all over the place but I will measure it up and post the dimensions when the car goes on the rotisserie. 3 Link to comment Share on other sites More sharing options...
ConVerTT Posted March 3, 2019 Author Share #15 Posted March 3, 2019 (edited) Someone was asking about how the jig can be used to re-align body panels ... basically BFH... I had to pull this backer plate forward about 1/4” and down about 1/2” to repair previous accident damage. Easy peasy .... Depending what you need to do, you can use pry bars, come-alongs or whatever for works .... Edited March 3, 2019 by ConVerTT Typo 3 Link to comment Share on other sites More sharing options...
Patcon Posted March 3, 2019 Share #16 Posted March 3, 2019 11 hours ago, ConVerTT said: Someone was asking about how the jig can be used to re-align body panels ... basically BFH... I had to pull this backer plate forward about 1/4” and down about 1/2” to repair previous accident damage. Easy peasy .... Depending what you need to do, you can use pry bars, come-alongs or whatever for works .... How did you attach to the backer plate? Did you bolt a strap to it? Some good frame clamps help a lot in this situation Link to comment Share on other sites More sharing options...
ConVerTT Posted March 3, 2019 Author Share #17 Posted March 3, 2019 1 hour ago, Patcon said: How did you attach to the backer plate? Did you bolt a strap to it? Some good frame clamps help a lot in this situation Yes exactly. I couldn’t get a decent grip so I just looped a strap from a scrap piece of sheet metal and bolted it on Link to comment Share on other sites More sharing options...
Patcon Posted March 3, 2019 Share #18 Posted March 3, 2019 I have a selection of Mo-clamps like this. They are not very expensive but they grip tighter the harder you pull 1 Link to comment Share on other sites More sharing options...
ConVerTT Posted March 3, 2019 Author Share #19 Posted March 3, 2019 3 minutes ago, Patcon said: I have a selection of Mo-clamps like this. They are not very expensive but they grip tighter the harder you pull Hey Thanks Patcon! Those would be perfect. Where to buy? Link to comment Share on other sites More sharing options...
wheee! Posted March 3, 2019 Share #20 Posted March 3, 2019 Mo-town? 1 1 Link to comment Share on other sites More sharing options...
Patcon Posted March 3, 2019 Share #21 Posted March 3, 2019 I buy them off Ebay or Amazon. More challenging for those of you North of the border. I try to get one like this, then I have one that has more room behind the jaws to get around flanges and such and I have one that will join up 10 or so weld on studs to pull. I also have a wide one that has double jaws 1 Link to comment Share on other sites More sharing options...
Patcon Posted March 3, 2019 Share #22 Posted March 3, 2019 (edited) https://www.ebay.com/sch/i.html?_from=R40&_trksid=p2380057.m570.l1313.TR6.TRC1.A0.H0.Xmo+clamp.TRS0&_nkw=mo+clamp&_sacat=0 Lots of styles and types. Some have dual points so you can load it in two directions at once. If your jig was fastened to the floor you could add pull points in the floor and some cribbing and basically have a 240z frame rack Edited March 3, 2019 by Patcon 1 Link to comment Share on other sites More sharing options...
240260280 Posted March 3, 2019 Share #23 Posted March 3, 2019 1 Link to comment Share on other sites More sharing options...
ConVerTT Posted March 3, 2019 Author Share #24 Posted March 3, 2019 38 minutes ago, Patcon said: I buy them off Ebay or Amazon. More challenging for those of you North of the border. I try to get one like this, then I have one that has more room behind the jaws to get around flanges and such and I have one that will join up 10 or so weld on studs to pull. I also have a wide one that has double jaws Thanks Patcon! And yes I wish I had a few D-ring anchors in the floor for many reasons too! 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now