Needed fasteners!

[JLPurcell]

I am in need of the fasteners for the rubber bushing retainers for the brake, fuel, and clutch lines. Does anyone have or know of someone who might have a set. Are they still available? Thanks in advance for your consideration.

[Patcon]

The little tiny hex head bolts?

[CanTechZ]

They are M4 like this, not sure of the length. I think they only have a lock washer

https://www.clipsandfasteners.com/M4-0-7-x-8mm-Phillips-Hex-Head-SEMS-Screw-p/pm33209.htm

[jfa.series1]

Hi Jerry,

I did a quick check on my car - the tiny bolts are a 7mm hex head with a phillips slot. Checking with Belmetric, it looks like they are called SEMS Hex Phillips altho these have a flat washer installed. They carry it in a 6mm head but not 7mm. https://www.belmetric.com/sems-hex-phillips-c-10_2345/?zenid=2tdb29vtv11hqsruk3uf0dsk12

Interesting that Nissan used a odd number mm head when everything else is even number.

Jim

[CanTechZ]

I thought all of my screws were deep in my crawl space but I found one, length is  12mm and it is an M4 x 0.7 with a 7mm hex plus JIS phillips head as @jfa.series1 mentioned. Jim I think the screws you linked to are M6, not 6mm hex head. It does seem they are like SEMs but with a lockwasher only, at least it is that way on my 7/70.

 

Just checked and Clips and Fasteners has them in 12mm long as well.

https://www.clipsandfasteners.com/M4-0-7-x-12mm-Phillips-Hex-Head-SEMS-Screw-p/pm33211.htm

 

Edited September 6, 2021 by CanTechZ

[jfa.series1]

11 minutes ago, CanTechZ said:

I thought all off my screws were deep in my crawl space but I found one, length is  12mm and it is an M4 x 0.7 with a 7mm hex plus JIS phillips head as @jfa.series1 mentioned. Jim I think the screws you linked to are M6, not 6mm hex head. It does seem they are like SEMs but with a lockwasher only, at least it is that wat on my 7/70.

 

Just checked and Clips and Fasteners has them in 12mm long as well.

https://www.clipsandfasteners.com/M4-0-7-x-12mm-Phillips-Hex-Head-SEMS-Screw-p/pm33211.htm

 

You are correct. In my haste I misread the specs as a 6mm head but it is indeed a M6 screw dia. Thanks for catching my mistake.

[CanTechZ]

7 minutes ago, jfa.series1 said:

You are correct. In my haste I misread the specs as a 6mm head but it is indeed a M6 screw dia. Thanks for catching my mistake.

You're welcome. Funny thing is when I was doing a quick search for these, that was the first link I found and almost posted it as well.

[Zup]

https://jdm-car-parts.com/collections/hardware-parts-nissan-datsun-fairlady-z-240z-260z-280z-280zx/products/brake-clutch-line-holder-bolts-x10-set-jdm?variant=643769873

[Patcon]

Is clear zinc the correct finish?

[JLPurcell]

1 minute ago, Patcon said:

Is clear zinc the correct finish?

Honestly I don't know if yellow or clear is correct? Anyone?

[JLPurcell]

1 hour ago, Zup said:

https://jdm-car-parts.com/collections/hardware-parts-nissan-datsun-fairlady-z-240z-260z-280z-280zx/products/brake-clutch-line-holder-bolts-x10-set-jdm?variant=643769873

Zup, thanks for the lead!

[JLPurcell]

35 minutes ago, Patcon said:

Is clear zinc the correct finish?

It seems that clear zinc is correct. At least that is what is on the 70 - #00869 in my driveway. JLP