Leaderboard

My next place is gonna be about a 1200 sq ft cabin and an 8000 squ ft shop. My 1000 squ ft shop is nowhere near enough and I want inside storage for all my cars

Man I wish I had the space for a blast cabinet... I would use it all the time. A few more years until the kiddo is out of school and I'll be looking for a place with a shop.

So I have a Harbor Freight blast cabinet. It is probably 15 years old or older. I have wanted to do the Tacoma Company upgrades to it for years but I've never pulled the trigger because the timing was always bad. I finally bought the pieces last month. https://www.tacomacompany.com/ The original cabinet Cut the bars out from under the frame New funnel adapter on bottom of the cabinet Drilled a hole in the left leg for a new air regulator Two new holes for the air and media for the gun Regulator Cut the lower shelf back New box that covers the air intake on the left side of the cabinet Air flow is reversed in this new setup I had to silicone the screws at the glove cuffs because the static from the cabinet would shock the fool out of you Cut the spring steel screen down and wrapped it with metal screening to prevent little parts falling down in the cabinet Added a foot pedal for the cabinet versus a hand trigger New gloves inside and a fresh piece of glass I have a switch on top that cuts the LED's on in the cabinet and start a vacuum that sits outside the shop door I finally got the air all hooked up today. It's a totally different cabinet now!! I can see and it cuts really quickly. I have some new Bufferfly screws for a quick change glass setup

Rear are different to the front and even the lhs rear is different to the rhs rear; it has a slightly different angle on it from my memory.

Wow, that Tacomacompany stuff is top notch. I’ve made all kinds of mods to my Harbour freight/Princess Auto cabinet over the years, and it woks pretty well, but I see the advantages to almost all of their products. Will be upgrading the feed and vacuum controls for sure. The one huge thing I recommend is to make the top glass area into your access door rather than the big door on the right. My compressor is right there, never able to get bigger parts in there anyway And use plexi sheets instead of glass. I buy a 4x8 and chop it up into 16x24 pieces to fit my frame. Disposable and cheep. I use cheap LED strip light strips ringing the entire inside top of the cabinet for lighting. They are surviving just fine. What really amazes me is the amount of sand that makes out of my supposedly sealed seams….

Exactly!! I've had the same discussions here. Not that it'll ever happen, but...

The Mikuni gasket kits (US) don't have in them the pump diaphram, did you get those separately? https://www.jauce.com/auction/1155785394 This what they look like if you don't know. From my experience the gasket kits from Japan do/more likely do come with the pump diaphram than the US kits.

I Just came back from the workshop (more on that in the coming days), and realized I never posted about my recent purchases. Firstly, a set of L-series Factory Service Manuals in German language: The Lot also included a German training manual for Nissan OEM Register carbs. Mainly of the A-series and L4 Engines, but also of the L6 of the C230, etc. Not relevant to my project, so I'm going to sell it. The Lot also included the Service bulletin N0. 201 "modification of the 260Z 2+2, One which was missing in my collection of S30 bulletins yet: I also got the last piece of the puzzle to complete my Datsun Special tool wall. The Kent-moore ST-351-00000, for the front axle. I had it before, but the handle was missing, and now i found a complete one: Then I also got a bunch of Mikuni Performance Carburetor gasket rebuilt Kits Z70-1044, which should be the correct ones to rebuild my recently acquired PHH44 S5 Carbs Today I also got the US Market 1972 FSM, which should be the almost correct one for my model. I recently realized I had only a very early 1969 version and then later S30 generations ones, but never one close to my actual build. And then you can never have enough Factory documentation 🙂 The seller also had a bunch of OEM parts, so while buying anyway, I decided to throw in a set of NOS Hood bumpers in the order: I've been busy working on the car myself in the recent days, so expect more updates on the project soon.

Hi Jase, I suspect you are experiencing possibly two effects of your updates. The first is likely more of a "new car" ride where everything is nice and firm and no longer the 47-year old squishy. Add on that the second item which might be the age of your tires which become harder over the years. Old (and larger) tires will certainly transmit road issues thru fresh and firm bushings and shocks. Last year I swapped out my 12-year old tires (still with lots of tread) for new ones and the difference in the ride quality was significant. Jim