zKars

Ok, working on another early Z today and find the worst case of crooked engine mount I’ve ever seen. Mostly I want to know if any one else has noticed this and actually found the reason. I’ve seen it on several cars, all “early”. 70-71. Yes I know they vastly strengthened the later ones, maybe starting in 74 with bracing across or between the two side pieces, so it must have been noticed by Nissan. Feels like its in the time line of the early cars that had the diffs mounted too far forward, I suppose with age, the bushings in the diff and trans all get weak and the engine tends to move forward. But this one is bad. Mind you the rust on this one is pretty advanced. The floors and trans tunnel might not be the best supporting cast in this situation.

And finally life makes sense! I just realized what that piece of scrap used to be! And only you would zoom, google that PN and find out what it was. I first thought that on certain garage doors of a certain period or place could be manually wound up or down with a crank and you were just wondering why I repurposed mine to this use. Silly me.

Ok here is the second tool I promised. Didn’t have pics last night. It relates to loosening old rusty brake line nuts. How many of you have been forced into vise grips on a brake or clutch line nut because your fancy flare nut wrench spreads and slips around a really old and tight one? Come on, fess up, we all do it. You get it loose, sure, maybe with some heat, but the hex of the nut is invariably wrecked. When you go to put the line back on, now you HAVE to use vise grips to tighten it, and the hex soon becomes a circle…… I have tried MANY brands of flare nut wrenches, all are simply not good enough. So, I made my own! With a special feature. Here is the standard heavy walled flare nut wrench. My idea was to add some way of squeezing that wrench hex closed to tightly grip the hex of the line nut, so it CAN’t slip around. First approach was to dream of fancy levers and threaded things to apply the needed force to close down on that heavy open “C” and squeeze the nut, but even with my largest vise grips, I really couldn’t apply enough force to collapse the opening. Ok, so maybe grind down the wall thickness until its thin enough to give? Maybe, but why not find a thinner walled wrench to start with? Well there is no such thing. Unless…. So I just bought a cheap Amazon 10 mm 6point box end wrench and turned it into a flare nut wrench by using a thin cutoff wheel and making a 3/16 gap in the end! My creation on the left, standard flare nut wrench on the right. Now its easy to squeeze that gap with a 8” vise grip So you just place the wrench on the line nut, then close the vise grips over the “C” and squeeze it shut. Then apply all the force you want with a hammer or pipe or whatever it takes to break the nut loose without fear of stripping the hex. After extensive testing on several cars recently, this little jewel is working perfectiy! The only thing I need to do is make the handle longer so I can tug on it by hand without beating on it with a hammer all the time, especially when the room around nut is tight.

Two submissions today the first is a little “make a job easier” tool for testing manual transmissions or computing ratio’s in various gears. Its just the center spline of a worn out clutch disk with a hunk-o-scrap welded on with a handle. Now you prevent yourself (ok myself) from clamping vise grips on the trans input shaft splines to make it spin.

If you can’t find any closer, I have lots. Let me know.

Love a good necro-post! Thanks Do your bolts have a smooth round head with a flat on one side? Orient the bolt so that flat prevents the bolt from turning when you tighten the nut. Memory says the nut faces the back…..

The silver tin sill plates with (or without) the embossed DATSUN sit flush on the rockers. Better make that a butt weld patch.

Oh dear, I’m afraid it’s another case of YNUABEH (you’re not using a big enough hammer) With the bolts out, it free to rotate. Put a large pair of pliers, BA pipe wrench etc on it, and whack it with a BEH (see above)

Nasty job, no fun at all. I can only add to the above excellent advice with a small warning. I have tended to clamp vise grips on the turned lip of those clamps then found that in some cases, depending on the angle of applied force or degree of rust degradation, that the lips tend to break off. Then you’re in a real pickle. The true key to removal is to get them to rotate first to break the rust bond, THEN they will slip off more easily. You can use a chisel, screw driver etc to drive the clip to rotate it, just a bit, back and forth until that becomes easier, THEN work on applying force to pull them free.

I have brake switch and prop valves available. Let me know. I think MSA or one of the major vendors sells o-ring kits too.

Not really. By the time 280’s came out, I suspect any other model that might have the same item would have the M10x1.00 threads. But take nothing for granted

As long as you joined the ring terminals that were on the ammeter posts, then everything should work just fine. If you left them separated (and insulated I hope!) then ain’t nothing going do much of anything.

That is a very ingenious way of measuring/gauging wear on a timing chain. It doesn’t say much about stretch, but it does say something about pin wear. I’d have to compare it to a new chain to get idea of how much deflection is meaningful. Given the pretty reasonable price of a timing set (gears and chain and tensioner) I wouldn’t hesitate to put in a new set if I had the engine apart. I’ve never ever heard of a chain breaking, and stretch just means some mild adjustment of cam timing. At the extreme end of stretch you risk skipping a tooth or teeth and having your valves have a new angle on life (a very short life after that), but that is also extremely rare.

I just finished parting out what was left of a extremely rusty 79 slick top 2+2. I have the AFM and ECU if you want them for spares. Very very cheap. Only other things worth saving were the instrument cluster, steering wheel and maybe the right tail light.

Only the 81 ZXT got an oil cooler in North America. Not sure about anywhere else.

I am pretty sure the third image is not S30. Nothing there I recognize.

I can send you two of the ones I got, or you can order your own from : megazip.net 48128-78500 is the part number. Took less than two weeks to get to me. $30 USD to get them via EMS shipping. Remember they are the long right side ones, so the left side will need to cut flush once its pressed into the housing. Haven't done any yet, so help tips about how to do it, but I would heat the housing to 300-400 F in the over to expand it and freeze the bushing to make insertion easy(er). They are bronze or similar, so not very hard.... Jim

It is a 280 center valance. The lower and larger rad opening and bumper changes required the 280’s to have changes in the shape and fitment valance components. They are are interchangeable with the 240 parts. Even the signal/marker lights were moved out of the outer valance pieces

Just make sure you have the shift fork with the hole in it before you purchase the slave with the adjustable length rod. It’s ball shaped stopper seats in the spherical recess and the rest of the threaded rod pokes through the hole.

The symptom is that you can move the shifter to 1st and 2nd where they used to be, but nothing happens. It feels like there are no shift forks in contact with the end of the shift rod. I first though the end of the 1-2 shift rod fell off. But no, without that pin in place the shifter can’t rotate over enough to get 1-2 lined up so it essentially stays in neutral. 3-4 and 5-R feel normal and engagement is fine.

Put the “pin-stopper” back in and put the C clip back on. After you find it or get another of course. Simple! FS5W71B BTW Don’t ask me where the old one went. Put some sealer on either end as well, it could leak oil.

Welcome back. You never left, the Z-Force is strong within you and you can simply no longer resist it’s call. Resistance is futile. No wait…

Recenty bought some directly from Nissan.

Sp the question is, under what conditions would the springs break into so many pieces? The first break is above the packed mud. The remainder were all buried in the terra-very-firma