
Everything posted by Diseazd
-
Pinion angles( driveline operating angles)
-
Pinion angles( driveline operating angles)
-
Pinion angles( driveline operating angles)
I just put a 1983 ZX 5 speed in my 73. I had restored the tranny cross member on the tranny I removed and it had a brand new tranny mount and a 1/2 inch spacer (between the tranny mount and the tranny), so I used that crossmember, tranny mount and spacer. When I test drove it, everything was fine except when I stopped and made a hard right turn. At that point it made an irritating vibration noise on acceleration that lasted a few moments......kinda made you want to throw up! I kept driving it and it kept sending me weird vibrating signals that something wasn't right. I took it back to the house, raised it on the lift and proceeded to take off the crossmember, mount,and removed the spacer. Went back without the spacer......on the 2nd test drive, everything was perfect. A half inch spacer bunged up the works.....amazing how critical pinion angles to smooth function of the drive train are.Peter.....get rid of the GM mount....it's your problem. Steve keep using spacers to raise or lower the rear of the tranny until you get it right. When you finally get the correct angle, you'll love your cars again.
-
Rear Seal
Right you are Blue......that's how you get smart....by doing stupid things! At least I was going to swap the tranny anyway. :stupid:
-
Rear Seal
Just finished the tranny swap......while I was at it, I pulled the clutch and flywheel. The seal was dry, but I replaced it anyway. When I was finishing everything up, I noticed a drip of oil coming from the bottom of the heater hose. I lowered the car and discovered a pinched gasket at the rear of the valve cover........wasn't the seal after all.
-
New engine
Went to work on the Z Doctor P79 head today. I geometried all the wipe patterns for the Isky Stage III cam and valve springs. All rockers centered out with .160 lash pads except 2 which were .150's. I use an old egg carton to keep everything in order. Hope to start reassembly soon.
-
Reproduction tail lamp lens and trim
Thanks Chas.....Hot water worked like a charm.....5 minutes and she came right out! Just used hot tap water.
-
Reproduction tail lamp lens and trim
No problem....I just ordered a pair of the chrome strips....$200.00 with shipping....we'll see how they look. Anyone know how to remove the lenses from the housing? I think there was a post on that subject ......seems it involves heat, but not sure. Can you remove the old strip without removing the lense from the housing? Most of my lenses are in good shape....just the chrome strip that goes bad. Any help would be appreciated.
-
Reproduction tail lamp lens and trim
http://www.classiczcars.com/forums/open-s30-z-discussions/41722-240z-chrome-taillamp-strips.html
-
OK Inspection Sticker in right quarter window.
Call Mike at Banzai Motorworks.....he sells the reproductions and would probably be able to answer your request Jerry. www.zzxdatsun.com
-
replacing callipers on 73 240
Chris.....I'm not sure, but if I recall, they were from an early Toyota Fourrunner (maybe 1984)......If I were you, I'd get Conedodger's (Rob's)friend to rebuild your stock units as mentioned in post number 2 (Willoughby Z). That guy does an amazing job, and a rebuilt set of stock Z calipers will work as well as the Toyoshimo's with no cutting required. Unless you're racing, replacing the rear drums with discs is a major job (PITA). I'd stick with drums. IMO
-
Rear Seal
I'm referring to the crank seal.... Not the side seals.
-
Rear Seal
Did you use a Nissan seal? I'm going back with Felpro......It's such a PITA to replace too!
-
Rear Seal
Anyone else feel like the Nissan rear seals aren't up to snuff? My 73 just developed a pretty good rear seal leak. It has a new (blue) Nissan rear seal (2000 miles). Which seal works best for you? I'm going to go back with Felpro. I was going to replace the tranny with a 5 speed anyway, but it still makes no sense why a seal with that low mileage would start to leak. BTW, it isn't the groove that's the problem....I always allow for that.
-
Which Transmition? 4 or 5 speed with 390 gears & turbo..
My 3:54 with a B type 4 speed is running 3000 rpm at 60 mph in 4th gear. I wouldn't want to run a 4 speed with a 3:90 .......go with a 5 speed. IMO
-
MUST GO - HLS30 00201 - Project
Why would you need another Z Stephen? You've already got one.
-
What do y'all think of this color?
Sorry e-tek......I think I'd go with just the silver metallic.............why don't you ask your wife's opinion? :ogre: The work is awesome!
-
Ron Tyler Differential Mount
Why is everyone trying to "reinvent the wheel"? If you use the stock mount and the Ron Tyler mount with a bump stop, all you've done is installed a solution that is far superior to stock but at the same time kept the alignment that Nissan engineers intended. The stock rubber mount also prevents vibration from causing stress fracture of the cross member.....even if it damaged. IMO......Use the R/T mount with a bump stop and the stock rubber mount.....works great on all 5 of my cars.
-
The official "Post pictures of your wheels" thread
Jarvo.....I believe they are "0" offset. I'm running coilovers, so we can go as low as you dare. The tires are 225-50-16.....a tough tire to fit. They look great, but a 205-55-16 is easier to fit in the wells. Thanks for the compliment.
-
The official "Post pictures of your wheels" thread
-
Chain rattle after oil change
What kind of damper bolt and washer is in your damper? I used one of the Nismo damper bolt sets with the drop down washer once with a stock damper. When you torqued it up, it set down in the damper against the nose of the crank without really snugging up the crank pulley, worm gear and oil slinger. If the washer you're using isn't flat (as in one plane), this could be your problem. It results in chain noise and will drive you crazy trying to figure out where it came from.
-
The Way Back Machine- 1972 240z - 113 Froggy Green
git.....I believe the Panasport's are "0" offset on the green car.......I just ordered a set for the orange car from Spruell Racing in Atlanta. They have the best price on Panasports. I think they would look great on your green car.
-
The Way Back Machine- 1972 240z - 113 Froggy Green
Really nice restoration git ............done the right way. The end product will be awesome.......can't wait to see it. What money is made for!
-
Springs....Eibach oor Tokiko or what?
BlackDragon shows them available at $169.95 or maybe try Spruell Racing in Atlanta.BD phone is 1 888 789 3746.
-
A converstion about how much compression is too much for pump gas
Blue.....When you shave a head .080 inches without shimming the towers, how do you adjust the chain slop? With the P79 shaved .080 inches, we use the early valves (.080 inches longer) and shim the towers and springs up .080 inches to end up right where we started. Just curious with how you make the adjustment on an N47 shaved that much? Guy