Jump to content
Welcome Guest! Please read more information about our club!

Bruce Palmer

Member
 View Profile  See their activity

  • Posts

    1,610

  • Joined

  • Last visited

  • Days Won

    4

 Content Type 

Everything posted by Bruce Palmer

  1. Bruce Palmer
    Email me at ztherapy@msn.com and I'll hook you up with Greg. There's a club on the island too. VIDE Vancouver Island Datsun Enthusiasts. Stick with us, we'll get you up to speed.....
  2. Bruce Palmer
    Well, frankly any manifold will work 3 screw, 4 screw, or flat top, matters not. Flat top balance tubes are uglier than home made sin but other than that I believe the flat top manifold manifold might even flow a little better than the earlier manifolds. That is based ONLY on looking into the intake runners on both manifolds. We are also seeing more guys wanting to disable the water thru the manifolds entirely. Just one less thing to go TU and leave one standing beside the road...... Do you know Greg McCauley on the island? He has Some Z stuff. I know he has a primo early air cleaner he'd like to sell.....
  3. Bruce Palmer
    Which carbs are you going to be running? 3 screws have the provisions for water through the insulators into the carb bodies. How much cold weather driving do you plan on doing.
  4. Bruce Palmer
    until
    www.Datsunsnw.org for details and registration info
  5. Bruce Palmer
    Portland Oregon area. www.datsunsnw.org for details as they develop. Understanding that the same group of people have been doing the heavy lifting on this event for several years now I want to put the word out that should any of you who will be there like to volunteer an hour or two helping out, it would be greatly appreciated..... Don't need to be a club member to help out either. That's just how reasonable the club is. It's the fees that cover the costs..... It's the bodies that get it done....
  6. Bruce Palmer
    3 screws were the last carbs used before the infamous flat tops came out. 3 screws were used in conjunction with the manifolds that had the water ports between the bottom two mounting bolts on the inlet side of the manifold. Functionally no difference between them and their 4 screw brothers.
  7. Bruce Palmer
    I would guess "unhappy" module. Take it off the disrtributor and clean behind it so is isn't contacting the distributor body. Don't recall where I heard that but it was on the internet so it must be the pure quill.... I had a Maxima that had an "unhappy" module that was very sensitive to heat but by the time I'd pull into a lot and raise the hood it would have cooled down enough to start again. Just for grins, you might pull the float bowl lids and see if you have any accumulated beads of water rolling around on the bottoms of your float bowls. Another old wives tale that a bead of water can plug the outlet.
  8. Bruce Palmer
    Now, how aggravating would it be to turn out to be something as simple as that? Makes all the sense in the world. All you other guys writing this down?
  9. Bruce Palmer
    Yep, getting the "fuel pump running" thing in synch with the "engine running" thing certainly ought to be a priority. Nyuck nyuck.....
  10. Bruce Palmer
    Our best to all down there.
  11. Bruce Palmer
    I did my part when I asked the question...... Even a blind hog.... etc. etc. etc.
  12. Bruce Palmer
    What kind of induction system did the 2.8 have? I'd get a large container and take a fuel line in the engine compartment loose and just let the fuel pump run and see, if a minute or two into the run, the volume drops off significantly. Then unhook the gas line on the upstream side of the filter in question and let 'er run. Probably looking for greater flow rate here more than anything. OR..... just replace that filter and see what that does. You say after it dies it takes a bit before it fires up again. I'm guessing that is a delay in refilling the float bowls, hence constricted volume, me thinks.
  13. Bruce Palmer
    Exactly when and how does this starvation problem show up? After the engine shuts off is the fuel pump still running? Happened on the last engine and this engine and you haven't driven this one yet? Old and confused, so very very confused..... nyuck nyuck Do not adjust the floats......
  14. Bruce Palmer
    We've got 3 liter and larger motors running 46's.
  15. Bruce Palmer
    Very nicely done..... That's one ATTABOY in your column.
  16. Bruce Palmer
    And we sell a DVD that will show you how to install whatever you find......
  17. Bruce Palmer
    Now that is a sterling piece of info. If you are running near stock tire height you should be good to go with the white gear. Does the white gear need any reorientation in the tranny case to mesh the teeth with the drive gear?
  18. Bruce Palmer
    What rear end gears are you running now? From that ratio to the new ratio, it is purely that % difference, old speedo gear to new speedo gear. That's also assuming you aren't changing tire sizes also. With the sppedo gears that are available, you will more than likely only get close.
  19. Bruce Palmer
    A "purist" would leave all that stuff hooked up. Factory original pipe plugs? Now that's too funny......
  20. Bruce Palmer
    American Pipe taps are close enough to chase the threads and then install standard Allen head pipe plugs the soem teflon sealer. Don't have to chase arounf trying to find metric.
  21. Bruce Palmer
    And just that quickly we go from carb talk to...... well you know......
  22. Bruce Palmer
    Whatever you do, stop that dieseling ASAP or you will break the top ring lands off the pistons and you will be an unhappy camper. Carbon build up, timing too advanced. Turn the car off in gear with one foot on the brake and let the clutch out...... That'll stop the run on...... Check to make sure your choke cables have some slack in them when the choke is off and make sure the nozzles are returning to the full up position when the choke lever is off.
  23. Bruce Palmer
    HMmmmm.....
  24. Bruce Palmer
    If the manifold is specifically a 4 screw manifold it's 70ish. 3 screws were 72ish
  25. Bruce Palmer
    No not really other than working with needles. Being a variable venturi for most street applications an SU that's back to square one will do about all the average driver will need. And do it very well. What would be the application? We have a set of our standard production carbs on their way for the Targa Newfoundland as we speak.
×
×
  • Create New...

Important Information

By using this site, you agree to our Privacy Policy and Guidelines. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.