timsz

Should you put anything on the threads of brake line nuts, either to help with sealing or to help with removal in the future? Thank you, TimsZ

Thank you very much. The rubber bumper must rest on the suspension member( The engine mount crossmember)? TimsZ

Could someone please give me more info on where (pic), if possible, where the clamp goes. It mentions a rubber part in the other threads. What does that look like and where does that go. thank you.

[ATTACH=CONFIG]68115[/ATTACH]I'm putting an ACT clutch and pressure plate into 81 5-speed transmission. Will this clutch bearing sleeve holder work? It's 2 inches total length. If anyone has any info, thank you very much, TimsZ

Thank you very much, TimsZ

Is there different venting methods on some cars? On my car ( 71 ) the 1 foot or so hose that comes out the top of the fuel filler hose, goes to the expansion tank. Didn't i see pics. and talk about a tee that is on the 1 foot or so hose? Thank you.

Thank you very much, TimsZ

Here's the pic.

I'm having trouble posting pic.

I can't figure out where these go. There are two of them. Are they for the end of the emergency brake cable? Where are they attached?

Thank you very much.

In the repair manual it shows the rubber O-ring for the fuel sending unit on the outside of the unit. In between the fuel sending unit and the lock ring. Is that right? It doesn't seem like it would seal, being put together like that. Any help? thank you.

Thank you very much. Yes, they came with double sided tape, also. Thank you, TimsZ

Here's the pic.

I have an envelope with front fender marked on it. There are 6 of these with plastic washers and bolts with an allen wrench. Are they for the front fender for my 71 Z? Thank you, TimsZ

The armrest where it sits up against the door panel was crooked. The rubber inside the armrest made it not straight. I think most early Z's are like that. I dug out some rubber from the armrest. I dug some out from under the metal reinforcement. It bends easily. I filled it with lg. gap touch n foam. I wrapped small strips of gorilla tape around it before i filled with T n F, so it wouldn't distort. I put masking tape in bolt holes and on the armrest so i wouldn't have to scrape the T n F off of them. They turned out pretty nice. Now to paint. Will colorbond from black dragon bond enough to not wear off? Any info? Thanks, TimsZ

Thanks, TimsZ

Does anyone know the pin placement on the turn signal flasher for a 71Z ? Is the 12V in on the left, the ground on the right and the line on top. Thank you, TimsZ

Thank you very much, TimsZ

I have the bigger ZX front calipers for my 71 240Z and the stock drums in the rear. Would it make much of a difference in what master cylinder I put on? I have the stock 7/8 and I also have a 15/16. Thank you, TimsZ

That's great info. Thank's so much, TimsZ

I have coilovers with tokico illuminas for my 71 Z. Will I need bump steer spacers, if I have 17 inch wheels? Thank you, TimsZ

I'm repairing my panel ( cracks, holes, paint, etc. ) Plastex worked really well on cracks and holes. It's sandable. Apparently the whole piece was chromed, then the black was put on. I sanded the whole thing with 80 grit sandpaper. It made the chrome look really nice. No scratches at all. The pics. don't show how good it actually looks. The sandpaper took the black off the peaks of the texture and left black in the valleys, on the textured section. I think it looks pretty nice that way. I also used the sharp edge of a small screw driver to get paint off. That didn't scratch the chrome either. Some sections will need chrome, but I think it looks good and I didn't polish or do anything else.

I have a 12/71 240Z. The shifter that came out of it is straight with threads on both ends. After looking at many threads, can that be right? I have the opportunity to cut my tunnel now. I'm putting in a f54 block,83 close ratio 5 speed. After reading many threads, I don't know what will work.(shifter hitting tunnel, console). I read where I can use 240 shifter without cutting tunnel. Which brings me back to the first question about my straight shifter. Any info or help? Thank you very much, TimsZ

Thank you very much, TimsZ