HaZmatt
-
Posts
566 -
Joined
-
Last visited
-
Days Won
21
Content Type
Profiles
Knowledge Base
Zcar Wiki
Forums
Gallery
Events
Downloads
Store
Blogs
Collections
Classifieds
Everything posted by HaZmatt
-
Wow that looks better than what I had to start with!
-
Thank you! And welcome to the forum!
-
A little progress today. I received my custom plug wires, heat shield, manifold stud kit, and new valve cover bolts from Datsun Spirit today. I also installed my new 3 row aluminum radiator. I also hooked up my battery for the first time in over a year. No blown fuses or fires, so thats a good sign. No dash lights though...hmmm.
-
I got them here for my 280. the 3012 and 3013. I had to wait awhile for the rears that were on back order. Took about 3 months. http://thmotorsports.com/tokico/tokico-shocks-hp-series/hz3012/i-526535.aspx
-
Glad I could help. But yours look nicer than mine, now im going to have to take mine back out and repaint them Thank you sir.
-
It looks like the brackets that go from the center of the dash to the sides of the tranny tunnel.
-
Converting From Efi To Carbs, What Can I Get Rid Of?
HaZmatt replied to HaZmatt's topic in Engine & Drivetrain
This helps guys. Thanks. -
Converting From Efi To Carbs, What Can I Get Rid Of?
HaZmatt replied to HaZmatt's topic in Engine & Drivetrain
Wow I didnt realize these cars were so high tech! -
Converting From Efi To Carbs, What Can I Get Rid Of?
HaZmatt replied to HaZmatt's topic in Engine & Drivetrain
Thanks! Just what I needed. -
Heres what I used.. http://www.ebay.com/itm/Avery-Conform-Chrome-Car-Wrap-Film-Sheet-Decal-1ft-x-4ft-4-sq-ft-/110881493651?hash=item19d10d5293
-
Converting From Efi To Carbs, What Can I Get Rid Of?
HaZmatt replied to HaZmatt's topic in Engine & Drivetrain
Thanks Blue! Well I purchased an electric low pressure fuel pump that I was going to replace the stocker with. This wont work with the factory wiring harness near the fuel tank? -
Converting From Efi To Carbs, What Can I Get Rid Of?
HaZmatt replied to HaZmatt's topic in Engine & Drivetrain
Ok so i'm removing my harness completely. Can I just remove the ECU as well? I noticed theres a couple relays or resistors under the dash that its connected to. I can remove these too? Thanks. -
Yeah its a hobby knife with snap off blades. I think in 77 they got rid of the chrome strip.
-
I "re-chromed" my door panel strips today. I bought some chrome vinyl wrap off Ebay and cut some strips and applied it with a heat gun. It turned out really nice. Heres what they looked like before, typical chrome peeled off exposing blue plastic. Applying the chrome vinyl. Heated it up with a heat gun, tucked the edges with a bondo squeegee, then trimmed off the excess. Much better. Did the same with my rear dogleg panels.
-
I believe I do, not sure if it worked. Honestly I dont even know what it does. But I was planning on selling the whole EFI system as a whole.
-
Thats good advice. Thanks. Very true! Thanks Will do, it was a tough decision. Honestly I probably would've been happy either way but I'm more of an old school kinda guy and just love the look and sound of triple carbs on a L6!
-
280Z
-
-
From the album: HaZmatt
-
From the album: HaZmatt
-
From the album: HaZmatt
-
From the album: HaZmatt
-
From the album: HaZmatt
-
I sanded down the letters on my red valve cover. Used 100 grit then 320 then some scotchbrite pads to shine them up. I think it looks pretty good. I also just ordered new valve cover bolts, spark plug wires, and a heat shield from Datsun Spirit.
-
What filter do you recommend during break in?
-
I still need to do quite a bit of cleaning and polishing on the motor. Hopefully once I do a couple coolant flushes it will clean all that light rust out. Any suggestions?
