Jump to content
Welcome Guest! Please read more information about our club!

Johnny wick

Member
 View Profile  See their activity

  • Posts

    2,204

  • Joined

  • Last visited

  • Days Won

    2

 Content Type 

Everything posted by Johnny wick

  1. Johnny wick
    One of the plastic balls is worn
  2. Johnny wick
    Anyone?
  3. Johnny wick
    Where can i get one of thes 7 inch long throttle link replacement? There is a supplier on ebay who sells a modern type which is adjustable.
  4. Johnny wick
    Thankd
  5. Johnny wick
    How exactly do you fasten this seatbelt holder?
  6. Johnny wick
    I dont remember. Somewhere on the web.
  7. Johnny wick
    I dont have hot start problems. The engine does get very hot when idling in long traffic jams. Still dont know if it is percolation or vapor lock. I was considering if removing the fan clutch and putting two electric fans will solve this.
  8. Johnny wick
    Thanks guys. Problem solved. I tightned both nuts and the reinsert the spacer.
  9. Johnny wick
    Still trying to tighten the right rear nut of the right seat. Seems complicated though. I guess i will have to loosen the plastic nut underneath first and then try to tighten the small nut.
  10. Johnny wick
    Still trying to tighten the right rear nut of the right seat. Seems complicated though. I guess i will have to loosen the plastic nut underneath first and then try to tighten the small nut.
  11. Johnny wick
    I took some aditional pictures and found out there are some nuts under
  12. Johnny wick
    Which metal nut? All i see is a plastic washer and a plastic nut.
  13. Johnny wick
    I thought it only had a plastic circular washer and a plastic nut fastened to the bolt. Let me see if i can take a closer picture of what i have there.
  14. Johnny wick
    Anyone???
  15. Johnny wick
    What about the size and type of screw that goes through the steering wheel shroud and into the turn signal switch
  16. Johnny wick
    im trying to tighten the rear left nut on the driver and the rear right nut on the Passenger seat on my 1972 240z but it seem useless, All the other 3 nuts of each seat are tight and have their plastic spacer also. Could the nut be damaged or am i missing something here? I have attached some pictures as reference. The 4 plastic nuts must be tight. However, this is not happening with these 2 nuts. Anyone?
  17. Johnny wick
    Does any one know which type and size is the screw that goes accross the steering cover shroud and fastens here in the turn signal switch? My car is a 72.
  18. Johnny wick
    I just sent him an e-mail. Hope he responds.
  19. Johnny wick
    Just took the measure with a caliper. Its 20mm! Who sells this size of rubber plug?
  20. Johnny wick
    Any idea of what is the correct rubber plug?
  21. Johnny wick
    Maybe i should measure the diameter with a caliper first.
  22. Johnny wick
    Does anyone knows what size and type of round rubber seals go in these holes on the floor behind the seats? Who sells them?
  23. Johnny wick
    Just installed the pair of Msa 3 point retractable seatbelts in my 1972 240z. There are okay and rub a little bit on the neck. I will keep the original ones as i would like to restore them. I did opened a hole in the carpet and jute as the gear look better over the carpet. Any recommendations?
  24. Johnny wick
    Ok. Thanks
  25. Johnny wick
    Question: Should i spray some WD-40 on the springs and mechanism inside of the door. I read some people even use this product: http://cyclo.com/cyclo_product/liqui-shield-2/
×
×
  • Create New...

Important Information

By using this site, you agree to our Privacy Policy and Guidelines. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.