Johnny wick

Thanks so much. I will check

Yesterday the window of my driver door in my 240z got shifted due to slamming the door to hard. I had to remove the window crank and panel and discovered that some bolts were missing. The original window regulator works fine but some bolts should be replaced. Are they available? Who sells the hardware?

I have the Gen II mini evaporator with a Sanden 508 compressor on my 240z and believe me it lacks blowing power. I am trying to search for a better option.

You still have not told me how did you installed the retro belt msa seatbelt sets. The kit even brought this holder but no instructions on how and where it is installed.

Just got the complete set lf msa 3 point seat belts for my 1972 240z. Will i be able to use the stock receivers or just the one from the kit. I read that i also have to remove the center console to fasten the buckle holder in case i wont be able to use the stock ones. Anyone?

I circled the part that melted. Plastic shrink tubing that isolates the o ring terminal. I thought i could remove the plastic casing on the fusible link to slide a new shrink tube but it seems not possible. I took some other pictures where you can notice that i wrapped some 3m electric tape to act as insulator. It seems not possible to remove the casing to insert a new shrink tube.

The other day while changing the negative battery cable i accidentally bridge the positive and negative cable ends with the socket and burned the shrink tubing insulator of the fusible link. I tried to remove the plastic cover of the fusible link to insert a new shrink tube but it seems impossible. Should i buy one new or should i just wrap some 3m electrical tape where the shrink tube was? What if i leave that o ring connector naked?

No heater. I removed that crap. Ac hoses

Just sourced this one. Thanks for your recommendations mark. I accidentally blew the fusible link shrink wrap off so maybe will order one if needed.

What is the gauge for the firewall ground cable? I know its 9 inches long but what gauge? This is the one that is fastened to my negative pole and that i wish to replace.

those wires are too long. I am looking for a 24 inch wire.

Still looking for Negative battery cable with soldered terminal and extra wire to fasten to firewall. No luck yet! Anyone?

Mine is 1/72 Negative battery pole disconnected, tap given with closed fist to the gauge, needle went tobñ center and viola ammeter working again. Thanks to all of you for your great help throughout these 4 years and exhaustive patience. Happy new year!

WHere can i purchase a 24" high quality negative battery cable with a soldered terminal and additional 4 inch cable which will be fastened to the firewall? Maybe something similar. I would prefer the original negative battery cable for my 1972 240z. https://www.autozone.com/batteries-starting-and-charging/battery-cable/duralast-battery-cable/570458_310040_0 Please advise if it the original negative battery cable was 24 inch long?

thanks PATCON. I did not use CRC soft seal nor anything. I was wondering if i should use a Dremmel with a brass brush tip to clean the rest of the sockets on the remaining 3 side marker lights instead of replacing them all. THe only one that was really rusted is the one in the picture. Should i spray any product to keep the humidity out of the socket and avoid rust?

Yes its fixed. The contacts on the license plate lamp were also full of rust and a bulb was shut. I would also like to buy one of these lamps. Well i just got a full set of marker light replicas made in thailand. I spliced the ground and positive cable and crimped new bullet terminals. I prefer using the old rubber which seems fine, the original lens and the original metal frame. Would you recommend also spraying some CRC soft seal to avoid any future rust or could this product damage the rubber seal?

Well i just got a full set of marker light replicas made in thailand. I spliced the ground and positive cable and crimped new bullet terminals. I prefer using the old rubber which seems fine, the original lens and the original metal frame. Would you recommend also spraying some CRC soft seal to avoid any future rust or could this product damage the rubber seal?

I turn the bracket around to get a tight connection. Is this fine?

How much? Any pictures?

I dont have an account in the us. He should start using paypal or credit card.

What about the smaller wire with yellow terminal that is fastened to the firewall in the chassis. Should i replace it also with a thicker gaugr wire?

Is this negative pole grounded correctly to chassis? As you can see there is an additional ground cable fastened to the chassis. Should i use another gauge for this?

He doesnt accept paypal nor credit card. Any other option?

im having this issue again! My 15 amp fuse at in the fuse holder of the Parking light Harness provided by Dave Irwin went south. I guess its easier to disconnect the specific rotten and rusted red marker light at the rear , install a new 15 amp fuse and see if it blows again. I bought 15 fuses as they are very cheap. Do you think the power cable could be sliced somewhere under the dash also?

I guess ill have to test my car again in a big traffic jam with the ac on and see how it behaves before spending more money and throwing more devices in the engine bay. No more spending money on useless stuff.