sinnersahuayo
Member
-
Joined
-
Last visited
-
I gave her a shower and a hard test drive. still need u-joints.
-
So i start working on the DR side rear arm and looking at the pass side. I copy with the flat part facing down. It took me 2 hr extra until i figure it out. control arm are interchangeable with driver-side and passenger side. you just have to flip up or down. I did one side at time. rear arm poly bushing finished. I will have to test it out and hard. I still need the mustache bar and front arms those are easy I hope.
-
Here is a video of me pull toward me and you could hear it.
-
bought some new used toy for me. My Dewalt light fell and broke. I went to the swap meet on Sunday and bought 2 light for 10 and a impact gun for 30. My new parts for my Z are polyurethane bushing, 2 spindle stud and locking nut. Also at Ace propane torch and black paint. It was easy taking part out. The two bushing near the gas tank where gone and the metal sleeve. The other one I had to grind down. I used my best friend the saw-all made easy work on the spindle stud. The end just fall out and the rest of the bushing i just burn them out. Strut housing was a different story. 30 min of heat and trying to beat it out with no movement. I just call it quit. Took it to the only machine shop in Kitsap Co 32 bucks later they had it out. Clean them up de-grease them and the wheel well also. Painted the part and let the wheel well dry other night. One side at a time. I think am going to make my spindle puller when I finish pass side. Also took my bumper off and motorcycle exhaust form PO.
-
what is this switch and how to put this plastic parts. I also got the light on expect for for the headlight. I have checked the fuse and no luck. any ideas
-
sorry my light was weak and audio may be crappy but its runny
-
So i had to wait for a long time for my new parts crank bolt/washer/woodruff key and Used pulley 2 grove. It was easy putting everything back. Do I need smog/vacuum pump or i could just take that off? I start adjust the carb with my new toy. Still wait on my poly bushing and spindle pin.
-
I have done this on other car with good results. Aluminum radiator dissipate heat faster, any extra row will help any radiator aslong cooling system is working correct, and also look nice. The down side heavy xx fluid, and mental is softer. It great for city driving/tracffic, stop and go. I would stay away for ebay stuff but that my idea opinion. If you do replace any radiator I would take the radiator out and turn the car on and flush the system with a hose (bottem). Fan is off/removed. I seen other friend replace a radiator in a 66 mustang when I open the radiator and see inside i could see metal debris on his new radiator.
-
Am looking for the front crank pulley 2 groove? If you have one please let me know. My pulley has a crack on the woodruff key slot.
-
I had the running, did the valve adjust. I did check all the hose/line by press them with my thumb and index finger. With a Carb clean I spray the crab gasket and line to check for any leaks. Did the timing, plugs, clean the Dizziy. I see your from Seattle. I live in Bremerton WA for the time until they move me again.
-
I was also thing if anybody has one I could trade. I have a lot of extra some just look at my pic. Please let me know.
-
The key came out like that. It did not slip. Am looking for a mew one and hard to find. Same with the woodruff key. If anybody here has one please let me know.
-
I got your pic for the switch
-
I had to wait 2 day for my oil seal cuz a new girl at auto store part f-UP. It was easy taking everything off. Took me longer to drain the coolant. Crank bolt was easy with the help of the start. The pulley came off with a big crow bar???. Now I start to crank the engine and battery doesn't have enough ball to spin the engine. CCA is 600. I may need a deep cycle battery with more CCA. Also cleaned the front of the engine. When I was putting back the KEY and pulley found a nice crack the pulley. Need help looking for a good used pulley. I put everything back so I could move the car but need a battery upgrade.
-
I have been wait for my front crankshaft seal to arrive and will get those picture for you. Also I have tried to place the plastic cover around the steering columm and seem I may have the wrong one for it.
