Jump to content

Davidz1911

Free Member
  • Joined

  • Last visited

  1. I got it guys!!!!!! thank y'all so much for guiding me through so i didn't loose my sanity!! it was the relays and the hack job of wiring that caused it.
  2. I wasn't talking about hybrid, you were actually very helpful and it allowed me to articulate what i was seeing happen better, i posted on zcarforum and i got lit up by people bashing me. I am in process of running another pressure yes, this time for an extended period, the first time i tested it between the filter and the rail and it was about 36 psi. as for the EFI relay, is there anyway other than opening the harness to match these wire to the correct prongs? i don't see why there are 5 blue wires and 1 green wire, that just makes it difficult to know which goes where. Thanks guys!
  3. hey guys! thanks for all the awesome replies. If i was using the wrong terminology about the "no start" vs "not staying running" i apologize. I have replaced the fuel filter in the engine bay, I disconnected the fuel line between the filter and the rail and let it run into a clear water bottle, the gas looked as clean as can be. I also replaced all the plugs, plug wires, coil, distributor/cap/rotor. I got to looking at the relays and someone did a hack job of the wiring. WHY i have no idea but they did. They bypassed the fuel pump control relay and so thats why my pump is running 24/7 even when it is just in "ON". one of the other relays, Judging from the wire colors i would say its the fuel pump relay, is super corroded and probably trash. The reason i say assume is bc these are all universal fuses someone put in here, apart from the fuel pump control relay which they jumped. I have new relays and will be swapping them all out, fingers crossed it just the relays. Oh i have the FSM and have been on AtlanticZ and gotten the super clear diagram. Because these no longer have the pigtails, I have to match up each color to the correct pin. however they aren't the same relays as in the diagram. I have them all hooked up correctly with new pigtails i soldered in, now my question. The EFI relay is a 6 prong relay, it has 5 blue wires nd 1 green wire. Can the blue wires be hooked up anywhere ? My logic was that it wouldn't matter as long as power and ground are correct bc when the releay activates it will supply volts to all the wires anyway, or is that completely wrong and I'm just an idiot? i will let y'all know what i figure out. thanks for all the help guys!! Oh one last thing, i had posted this in a few other Z forums and the people who responded told me i was an idiot and didn't know anything about what i was talking about. I come on here and you guys are so polite and awesome. I thought thats what forums were all about was sharing a common interest in our Zs and to help each other out, but i guess only you guys act like that. PS heres a pic of my 280z
  4. Hey everyone, I'm new to these forums but not to Zs or cars in general. I just bought my 1 owner 1978 EFI 280z from a guy in Dallas. Its in amazing shape, paint, interior are both flawless and the mechanical aspects were wonderful too. started up fast as my 2013 car does and ran smooth as can be. I Drove it the whole way back home in Louisiana, about a 200-205 mile trip. Drove like a dream. parked it in my driveway, the next day i took it out and it died on me while driving. Then it started back up fine and i got where i was going, it sat for 10 minutes and cranked but wouldn't start. it was too dark so i went back the next day and tried to get it running. Did my basic checks, while testing for fuel with ether in the intake it fired up while someone was cranking it, and i blipped the throttle and it ran perfectly fine and i drove it around without a problem for 2 days. Now its doing it again and will not fire and stay running. Spark is fine, No vacuum leaks anywhere at all, new fuel pump and filter, new plugs and wires and coil and cap/rotor. its getting pressure to the rail, spraying ether in the intake will make it run but as soon as the gas is pressed it dies. If you don't press the gas it will eventually stall out snd die. I run out of time to work on it due to lack of daylight. I will be checking for power to the ecu and to the injectors tomorrow. Does anyone else have any suggestions of theories on what it might be? Thanks for the help guys!!

Important Information

By using this site, you agree to our Privacy Policy and Guidelines. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.