Jump to content

sblake01

Member
  • Joined

  • Last visited

Everything posted by sblake01

  1. Do you know for sure that the fuel pressure is 35 (actually should be 36.3 according to the FSM) and each injector has a pulse and is opening and closing?
  2. sblake01 replied to Tonizx's post in a topic in Help Me !!
    Personal identity is more important than the sale of a car. I'd steer clear of this buyer unless he wanted to do it under my terms. In fact, I'd probably steer clear of him anyway due to the 'bad vibe' that scenario would likely have given me.
  3. It says the current bid is 1,561,000 JPY. Wouldn't that be more like $15,000 USD?
  4. I had to laugh at that one even though you're talking about a pretty serious situation. Remember, Tina came out much better in the long run after the experience. Good luck down there, guys.
  5. My cars are about as 'done' as I'm going to do with them. They run and perform properly, everything functions on them, and they look halfway decent. Sure, there's always something that could be done to make them 'better' but I have more important thing to do with my money. What you said, Arne, applies to how I view each of my vehicles.
  6. sblake01 replied to Larry G's post in a topic in Open Discussions
    Thanks, Randy. I haven't been down that way for a while. Next time I visit my stepmom or son who both live in Pomona, one in NW Pomona and one in NE Pomona, I'll drive by Elvan's and see if he's home.
  7. When you say "leaks fuel from the injectors" do you mean that the hoses leak, in which case you could simply replace the hoses, or that the injectors leak fuel into the cylinders? You've already purchased new ones so I guess none of that matters now. Two things happen with old injectors. Either the coil insde them burns out, in which case I wouldn't bother with them, or the nozzle gets clogged causing them to stick. If they stick open, they leak into the cylinder and if they stick closed they don't inject fuel. As long as the coil is good, I use my pressurized cleaner and a tester I made to pulse the injector while I run the cleaning solution through it. Once it's clean and the nozzle properly opens and closes, I replace the pintle cap, the small and large seals on the bottom and the hose. Basically, that's what a shop does to 'refurbish' them and they charge more than I think that job is worth. If you send them to a shop that actually disassembles them, replaces the coil (if necessary) etc. and reassembles them, the labor alone would make that type of rebuild cost more than buying a replacement injector. As far as removing them, I remove them with the fuel rail so that you're actually pulling all six of them at once. That's the easiest way. Be careful with the screws that hold each injector in place as the heads on them strip easily. I replace those screws with allen head screws for future dissassembly. The clamps can be reused if they are in good shape but I'd use new seals and of course new hoses. Hopefully all of that stuff will come with your 'new' injectors.
  8. sblake01 replied to CelticGhost007's post in a topic in Fuel Injection
    I corrected the word 'they' from 'the' and I don't care for the green text, sorry. Anyway, the stock fuel pump on a 78 is electrical. They're still available and as you've probably discovered, somewhat pricey. This is an area where I would suggest the OEM fuel pump and not the aftermarket one that most of the chain stores sell. And if you think you have problems now, wait 'till you put that Holley on it.
  9. sblake01 replied to Tim Walz's post in a topic in Parts Swapping
    Until Mitchka revived this thread, the only people posting in it were yourself and three members who, though for different reasons, don't post here anymore.
  10. Does it run? Looks to be fairly complete and not as rusty as some I've seen from what I can see in the pics. It will be some work but I think $1500 would be a good price for it in this day and age. I notice it has the 2400 cc valve cover. I'll even give you the correct 'OIL' cap for it. (Does anyone really still use dial-up besides my mother-in-law?)
  11. sblake01 replied to MariaAZ's post in a topic in Help Me !!
    You have to loosen the nut on the front of the pulley first. (and tighten is once the belt tension is set)
  12. sblake01 replied to the_cafe's post in a topic in Engine & Drivetrain
    I know that you can be. I won't say I knew it all along but I figured out your thing a while back. Well.....as much as one person can figure out another, especially on the internet:cheeky:
  13. sblake01 replied to MariaAZ's post in a topic in Help Me !!
    If you had loosened the long bolt that is behind the pulley, it would have loosened the tension on the belt. At that point, you could have removed the belt from the idler and carfeully fed it over the fan and removed it without removing the shroud or cutting the belt. I've done it several times on that type of setup. I guess it's too late now.
  14. You might owe Will an apology:)
  15. sblake01 replied to MariaAZ's post in a topic in Help Me !!
    Someone else will have to answer the question about smog pump. The bearing, which can be replaced, is the problem with your idler pulley. I've redone a few of those in the past. The bearing is available at most auto parts stores but they come in different sizes so be sure to match yours up as far as outer diameter and center bore diameter. Disassemble the pulley assembly, remove the snap ring, press the bearing out, press the new one in, replace the snap ring, reassemble the pulley assembly, re install it, adjust the belt tension and you're done.
  16. sblake01 replied to MariaAZ's post in a topic in Help Me !!
    Have you tried tightening the bolt? It might just be that the loose bolt is allowing the pulley to move back and forth on the bolt which is really a combination bolt/shaft.
  17. sblake01 replied to gotswap's post in a topic in Engine & Drivetrain
    Andrew, this guy is not for real. It's just some type of perverse game that he's been playing ever since he's been on this site. He can spell 'discount' and 'membership' but not 'store'? I think he's just looking for a reaction.
  18. sblake01 replied to the_cafe's post in a topic in Engine & Drivetrain
    I don't believe that the_cafe has ever asked a 'seriously asked question' since he's been on this site. I think he's having fun with us, for whatever reason, so we were just having fun with him.
  19. sblake01 replied to the_cafe's post in a topic in Engine & Drivetrain
    Let me take a shot at this: Shouldn't you just put the water directly in the gas tank? That way the tank of gas will last even longer because the car won't be using it up.
  20. sblake01 replied to the_cafe's post in a topic in Help Me !!
    Not funny anymore...you've been exposed.
  21. Steve, you're killing me!!!ROFLROFLROFLROFL
  22. sblake01 replied to the_cafe's post in a topic in Help Me !!
    After reading more of your other posts, I have surmised that I must be the one that's not getting it. You're playing with us all.....right? No one is really as STUPID as you portray yourself. Note to self: Never again respond to posts by 'the cafe'.
  23. sblake01 replied to the_cafe's post in a topic in Help Me !!
    You just don't get it....do you?
  24. There is another fix though it sounds somewhat temporart to me. I can't find the thread right now but IIRC, it involves moving the pickup hose to a fitting screwed into the drain plug hole and capping the original tube.

Important Information

By using this site, you agree to our Privacy Policy and Guidelines. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.