Jump to content
Welcome Guest! Please read more information about our club!

sweatybetty

Member
 View Profile  See their activity

  • Posts

    1,119

  • Joined

  • Last visited

  • Days Won

    14

 Content Type 

Everything posted by sweatybetty

  1. sweatybetty
    SWEET!!
  2. sweatybetty
    that valve stem looks like it has a shiny spot on it. it it was bent it would cause that damage since where it broke is the weakest point
  3. sweatybetty
    yep! which is row 1?
  4. sweatybetty
    always do your longest cut first, shortest cut last. that rule pertains to almost anything from framing to brake lines
  5. sweatybetty
    did you get the complete set of d caps?
  6. sweatybetty
    thinking out loud here. any way of getting starting fluid into #1 & #6, closing the valves and igniting it? a few head bolts threaded in halfway to keep the head in the immediate area, might be enough pop to break it loose. what about air pressure in those cylinders while driving wedges in?
  7. sweatybetty
    i found on my tank, the tube that the fuel pump hooks to was about 95% plugged with rust. i would bet between that and your fuel line, thats your problem
  8. sweatybetty
    i would love to see a pic
  9. sweatybetty
    you might try a local parts store. you might find a cap off another model with a gasket that works
  10. sweatybetty
    thank you. i had no idea it was there. but i see it now.
  11. sweatybetty
    its not a PITA, just noticeable. pretty low on the priority list
  12. sweatybetty
    im still debating the strut bar. i do like this one https://technotoytuning.com/nissan/240z/front-strut-tower-brace-datsun-240z-260z-280z-0 https://technotoytuning.com/nissan/240z/z-front-tri-bar-add
  13. sweatybetty
    that doesnt look bad at all. i think you scored
  14. sweatybetty
  15. sweatybetty
    just went into town to fill the tank and did another 35 miles. this pig pulls hard and nice. a/f mix is in the mid to high 13's on a hard 2nd-3rd pull, cruises in the low 14's. seems to have a weak spot right off idle, (a/f mix 15-16) no bog, but just noticeable. needs a front end alignment and the exhaust piping tweaked a bit and welded. it sounds SWEET! no tire rub as of yet. i was a little worried about that. overall, im very happy
  16. sweatybetty
    i used this on rubber parts with great results https://www.berrymanproducts.com/products/eco-friendly-products/berryman-chem-dip-carburetor-and-parts-cleaner/ it says that it is safe for plastics. i would try it on something that you can spare first
  17. sweatybetty
    excellent day today, cherry popped! the pig got a bath and 8 miles on the odometer. the suspension is very nice and tight, throttle response is good, but the brake prop valve needs a little tuning. going to do a few more miles tomorrow, get some fuel and then sunday plug in the tracking software for the a/f ratio meter. kind of hard to watch the meter and drive at the same time
  18. sweatybetty
    my new foams from msa are firm but comfortable
  19. sweatybetty
    i will lean to the yes side on the difficulty
  20. sweatybetty
    still for sale
  21. sweatybetty
    no, the sticker said 1/8", but the actual board was almost 1/4"
  22. sweatybetty
    if both keys fit into the locks and ignition, you can have one or the other re-keyed so one key fits both. i would have the door locks re-done since the ignition switch is new. not very expensive either
  23. sweatybetty
    i tried there and slum depot. they called it 1/8", even the sticker on it said 1/8", but it measured way thicker
  24. sweatybetty
    im wondering if maybe the tape is to keep metal particles from building up on the magnets, not to hold them in. just an idea
  25. sweatybetty
    the one that came with my car is around 1/8". cant find hard-board that thin so i ended up sanding it down to about 3/16" if it is too thick, i dont know if the plastic rivets will hold it in place
×
×
  • Create New...

Important Information

By using this site, you agree to our Privacy Policy and Guidelines. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.