240260280

Going to build a new house, garage, long driveway, ditches, etc. on some land we bought a couple of years ago so I figured this would save some money and have a fun factor. Janet OK'd so we bought it last night. 2015 Kubota BX25D with 37hours. It has loader, backhoe (with thumb) and is a 3 cylinder diesel..... now to learn "tractor'n" Similar Facsimile:

Covid Tuning SK Racing Carbs for a friend. BRE 46 Tribute

You have to tune for cruise first, then idle then WOT. Find the right idle jet that gives you ~ 14-16 at cruise then see if you can get 13.5 to 14.5 at idle with the same jet by adjusting the idle enrichment screws. Once you get this, move to WOT runs. Find the right main and air corrector to give you 12.5 to 13.5 from 3000 to 6000 rpm under load. note: Air correctors are used only to tune WOT main system.

These guys are great Ed: https://www.ebay.com/itm/6x-WEBER-45-DCOE-main-venturis-chokes-28mm-30mm-32mm-34mm-36mm-38mm-40mm/301942409851?hash=item464d2b8a7b:g:DwsAAOSw~19bCaSQ

https://www.youtube.com/watch?v=ljfJkPode_k

Here is a quick calculation based on the following general assumptions: Air Flow over a puddle of fuel draws fuel into the air flow The larger the puddle, the more fuel is drawn The air does not saturate with fuel Air flow is constant Depression over exposed fuel is constant and here are the SU assumptions: venturi effect of bridge is ignored effect of piston raising is ignored air flow is constant over exposed fuel puddle fuel depth in well is ignored exposed fuel puddle is proportionate to diameter of fuel well (2.54mm) minus the area blocked by the needle's diameter at the surface. Station one Top needle dia is 0.095" Station one Bottom needle dia is 0.094" Here are A:F Ratio calculations for lowering a jet for an SU carb with: Top of station (Jet drop = 0) AF is 14 with N27 needle dia of 0.095" reducing to 0.094" at bottom of station. The math seems to match observations ?

I don't work in China, that was a long time ago. I will never go there again... but Taiwan is great. I avoid China crap at all cost. Just bought a made in USA washer. Don't be such an arse!

Your attitude is similar to those who accept "too big to fail" and you accept the slavery that goes on in China to make the shitty products without batting an eye.... that is how we got into this mess.... although we've both worked in China I'm sorry but our standards and acceptance is very different. Taiwan is how China could be.... it is so sad that we have a country like China and do nothing about it. Too much hypocrisy.

If the Mainland Chinese Govt. : 1. Made this. 2. Knew its lethal effects. 3. Knew it escaped from their lab. 4. Failed to contain 5. Freely let it travel throughout the world then 1. All countries would hold them responsible financially 2. Their Govt leaders would be called to the Hague and sentenced for Crimes Against Humanity 2. All trade with China would be stopped until the government and political structure changed 3. The world would ostracize the country and work completely w/o them. 4. Once they changed their Govt structure and aligned with the rest of the world, then work to bringing back to the world stage would be considered. The leaders in Mainland China do not think like most of the world. The citizens are also abused by these gangsters so it is a grave error to think the leaders and the citizens think the same way you do.

Have a look at the videos here. I saw this $^!# all the time when I worked for Huawei. https://globalnews.ca/news/6905295/coronavirus-china-hostility-report/

Existentialism has been around for a long time. It is not healthy nor logical. Perhaps you should have a health check on your cognitive functions as this way of lazy thinking is not normal. Cause and effect, Action and responsibility. and understanding what the **** we are dealing with are priorities at this moment.

Look at the science and data..... then think about .... then comment.

One of the most contagious viruses ever, has no reserve in nature (even Ebola and SARS have these) and it appears in the middle of a huge city where a known scientist has been altering Bat viruses for the last decade (and much of her research on this has been published). Janet and I figured $^!# hit the fan from a lab in early Jan when we saw images like this on TV (for a virus that did not pass human-to-human).

Evidence building and pointing to lab in China: https://www.wionews.com/opinions-blogs/how-us-expertise-may-have-inadvertently-contributed-to-covid-19-296512 https://medium.com/@yurideigin/lab-made-cov2-genealogy-through-the-lens-of-gain-of-function-research-f96dd7413748

View Advert Weber 55DCO NOS in box. The big one!! 55mm. I was going to modify a carb intake and replace 2 X SU with 1 X 55DCO but I am clearing out my dreamer parts. I'll post pics and get series details soon. This guy has 2 more if you need 6 throats: https://vermont.craigslist.org/pts/d/55-mm-weber-dcoe-carbs/7109735286.html Advertiser 240260280 Date 05/02/2020 Price $400.00 Category Parts for Sale  

Finally sold my ITB's ? Threw in a few extras too:

That concept has potential.... groan.

TRUTH IS STRANGER THAN FICTION. DARE YOU TO WATCH THIS:

Yeah! Condensed is back! THANK YOU!!!!

FYI the 2 day drops in the graph above are sat and sun. The peaks are Mondays .

Do you hear air at this port?