AZDatsun

I have the https://www.thezstore.com/page/TZS/PROD/classic08a02b/40-4525 and I put the headliner in just fine but I don’t get how to put in the pillar and roof rail parts. The vinyl sections seem overly wide. Does anyone have this kit and do and I need to trim it down? I also am not sure where or if I should be tucking it into something. I am also just guessing I should first glue down the padding then glue the vinyl to the padding. Any pictures would be great. Sent from my iPhone using Tapatalk

Generally speaking you put one end connected to the one side and the other end connected to the other side. Just don’t go front to back or back to front that’s not really important it seems. Sent from my iPhone using Tapatalk

Awesome this is perfect! Sent from my iPhone using Tapatalk

Anyone making the base that the rear view mirror clips into? Mine is all cracked up and I am sure it is pretty common for them to crack. Sent from my iPhone using Tapatalk

Exhaust fumes come in through the rear hatch and taillights it’s very common make sure you have those sealed up good and gaskets on the tail lights also make sure holes in spare tire area are plugged Sent from my iPhone using Tapatalk

I think this might help area = PI r2 Sent from my iPhone using Tapatalk

Ok yep the blue line for the radio worked for switched power and there were two black lines one didn’t seem to go to ground maybe to a speaker. The other was ground and it works perfect now. Sent from my iPhone using Tapatalk

Hey that’s great I will check that out tonight and post back if it’s working Sent from my iPhone using Tapatalk

If I recall properly the radio is switched power my car also doesn’t have that installed anymore but I can test that out tonight Sent from my iPhone using Tapatalk

Ok just found more the gauge is 1.3amps Sensor is 1.2amps at 12v it says It’s an AEM 30-4110 Sent from my iPhone using Tapatalk

Instructions say connect to a switched 10-18 volt power source with a 10amp fuse I am thinking cigarette lighter now as the source for power Sent from my iPhone using Tapatalk

Sorry about the description it was vague. it’s down where the air/heat controls are located. I removed those since I no longer run air/heat so I made a blanking plate for it it’s an AEM gauge I was thinking maybe a wire from the stereo harness Sent from my iPhone using Tapatalk

What is the best wire I should splice into for the gauge positive? I have the gauge mounted in the middle of dashboard area Sent from my iPhone using Tapatalk

Ok that makes sense I didn’t know the 2+2 shared the same center console Sent from my iPhone using Tapatalk

This area it’s not a 2+2 car both my original and new console have this I have a 78 Sent from my iPhone using Tapatalk

Random question but what is the point of the rectangular hole in the back of the center console. I am putting in a new center console and never really figured it out. Sent from my iPhone using Tapatalk

I use the rear diff block plate and the front crossmember in the middle Sent from my iPhone using Tapatalk

What is the easiest way to remove these from the center console. I have 78 280z and want to take them all out to clean them and service them. I seems like they are stuck in there pretty good and I don’t want to break any plastic. I am referring to the row that contains the hazard switch/rear defroster Sent from my iPhone using Tapatalk

The 1/4” also on the vapor tank is gates part# 27002 Sent from my iPhone using Classic Zcar Club mobile

I got some at orielly this weekend for a run from the fuel tank to the vapor tank 5/8th gates part#27008 Sent from my iPhone using Classic Zcar Club mobile

How do you swap your vin tag over to the new dash? Sent from my iPhone using Classic Zcar Club mobile

So my review of the bmw rivets..I put in the rear quarter plastic panels only so far. They hold the panels tight and I believe they will work but I wish the head area was a larger circle the rivets I have are 10mm circles head and I think the Nissan ones are 13mm based on the specs a few posts up. I am going to use them for now and see if they work on all the panels. I have a 280z not sure if that matters though. I will update this when I put more panels in. Sent from my iPhone using Classic Zcar Club mobile

Odd that it mentions 2+2 model on page 25 in a 240z manual Sent from my iPhone using Classic Zcar Club mobile

Wow thanks for doing those measurements Sent from my iPhone using Classic Zcar Club mobile