MH77280Z
-
Posts
436 -
Joined
-
Last visited
-
Days Won
1
Content Type
Profiles
Knowledge Base
Zcar Wiki
Forums
Gallery
Events
Downloads
Store
Blogs
Collections
Classifieds
Everything posted by MH77280Z
-
Guys, this is the only rust area i have, the cowl. I am thinking of blasting it as the wire brush is not good enough. This is heavy rust but still no pitting like damage. Top is ok, Issue is how much i can blast on the lower area. Also i think the passenger side has air passage into the blower motor i believe? my blower motor and air heating works fine. I would assume all the media will just get into the blower motor and through that inn the ducts? How should i prevent that? or just seal that side and do it with hand, blast the center and driver side only?
-
That's interesting as i did not find any clips like these nor any double sided tape. Badges were metal, i will try these too.
-
Heating and prying worked pretty nicely. Just a bit more patience and go slow. And there was an abandant wasp nest 😆
-
Hey Guys, what is the best way to take these off? i am planning to get the car painted. I tried access them from inside by removing the inner panels but no luck. Looking at the new ones they have 3 pins. Should I just use a heat gun and pry them out with a screw drivers? They are a bit beat up too!!!
-
Headlight front marker wiring rubber plug this one plugs into the body where the wires go into the engine bay. Is there a reproduction available for these?
-
Front side rubber bumpers (How to remove) 77 280z
MH77280Z replied to MH77280Z's topic in Body & Paint
I am ok, i found the 3rd nut behind the plastic wheel wells.- 1 reply
-
- 2
-
-
Guys, took the two bolts out holding the front side rubber bumpers to the main front chrome bumper. Rear end of the side bumpers is help to the body near the side markers by something which i cannot locate from inside. I am hesitating yanking it out. What is that holding them?
-
Thanks guys would certainly contact Ron this time if this is the recommendation.
-
Looking at the tread Zclock does restoration vs guys in IL can do a quartz conversation. I am not sure how long the mechanical movement will last. They are old school and can go bad anytime. I am leaning towards quarts movement.
-
Hi, anyone tried this? mine doesnt work and I suspect old mechanical parts. Anyone tried quartz conversion?
-
Last time I locked my doors my ignition was in ON!!! Luckily I had found a spare few days back tucked in a small bag and tied to the inside of the front fender by the previous owner which saved me from some pain.
-
I am sure not many folks had seen this. Found one rarely…the knob that opens and shut the air duct near the legs/knees on the driver side 🙂
-
Thanks
-
I have not pulled the door panels out to see what is wrong but my door locks really are bad and the key barely move the lock up etc. even the key is bend. These original keys are also kind of not as hard. Has anyone replaced the 2 door locks? is it easy and any recommendation what locks to get?
-
Coming along… Appreciate the support of all you guys. It has been the lifeline for this Z.
-
Will live with this for now …
-
-
Inflated the original and it is not bad looking at all. I mean look inflated pretty evenly with a car inflator and inflated to 25psi in about less than 5 min. Seems to be holding air. I plan to let it sit for few hours.
-
https://www.ebay.com/itm/224608896506?hash=item344bbbc5fa:g:J58AAOSwGt1hQCTw I am just gonna get this Audi inflator and the battery connector you mentioned. Keep the original SST since I am a stock freak and forget about everything 😁
-
One more thing, what about a portable cigarette lighter car tire inflator? anyone tried that with the Z? will the lighter circuit provide the level of AMPs or will blow off the fuse if connected?
-
May be this has been answered in CO post. T115/70/14 wont fit the stock rims which the SST is on?
-
Continental SportContact 195/40 R14 This seems out of stock but this should go on the stock SST rim and walla - it will also fit the space in the hatch. I am currently running stock 195/70R14 on all 4 wheels. If I cannot find one had to resort to @Captain Obvioussolution.
-
Has anyone put the SST in the trunk inflated? I tried putting air in it while on ground and that thing was bubbling up like crazy and i had to stop. I dont want to rely on a canister and i dont have one either. The only spec which fit the tire well at the back is 195/40/R14 and that tire done exist ... Sorry yes i am trying to put an always inflated tire on this rim and also making sure it actually fit in the trunk. Anything bigger than 20in diameter with tire on wont fit in the space provide, thats why i quoted 195/40R14
-
Looking for 240z radio antenna switch (see pic)
MH77280Z replied to Dadsun's topic in Parts Swapping
These ones?
-
Some 240z parts I picked up. Let me know if something is needed. Free of cost. You pay shipping.
