Chino 240Z

Hey Bruce, I bet if you brought a case of those Videos to the MSA show, you'ld be able to sell everyone! My favorite part is the end of the second tape, the Z out on the track overtaking car after car! is that Steve? what track is that? oh and the footage of inside the SU at W.O.T. on the dyno! Now I just gotta get a roll bar camera mount for ours. Cheers, Craig

Hey Bruce, I bet if you brought a case of those Videos to the MSA show, you'ld be able to sell everyone! My favorite part is the end of the second tape, the Z out on the track overtaking car after car! and the footage of inside the SU at W.O.T. on the dyno! Now I just gotta a get a roll bar camera mount for ours. Cheers, Craig

I don't know, but I'd be afraid that those worms coming out of the roof would infest the whole garage and start eatting my good cars!

Hmm? Maybe put a small "CZCC" initials in the top corner of the passenger side windshield?

Didn't MSA mention something about an improved system of getting the cars inside and parked? Sounds like an early, early morning get down there and wait?

We'll be there for the Sunday show.

Cheeze Whiz I'm amazed that such big & tall people are in love with such little cars? Must be the TIGHT fit!

2 Large shirts, we prefer long sleeve, just say when.

I would also change out the fuel filter even if it was a new one that you started with. If you are running SU carbs, there is also a "last chance" filter screen in the fittings that feed the fuel float bowls that may need to be cleaned out, some people just run without them, but like I call em -last chance, I use em. Might check down in the fuel bowl to see that they are clean once you get ready to start it up again after cleaning the tank. Good luck.

Yea! That's it! I remember clearly now. Had to shock some of the half dead brain cells back to life. Now I just gotta go pull off the cover from the spare motor out back. Thanks guys! Chino

Last year on line somewhere I thought I saw a place to buy a chromed valve cover with exchange of the old one. Don't really want the up-keep of keeping a polished one polished. Chrome or nickel plated may be what I would like to do. Was I dreaming again or does anyone know of a place? Thanks Craig

Okay, no problem. Yeap it is now confirmed sold. Money is on the way, but if something changes I'll let you know. I don't want to step on the other persons toes (Cindy), she tells me I only own 49% of the car! But hey, I have turn signals, lights, doors, door panels, some misc. Z parts I am saving incase (that other person ) crashes the car and I need to rebuild! So as you put things together check with me, I also know of a secret stash of z cars, parts and junk is sitting and I'm trying to get access to it. . . we will see? Thanks for understanding. Craig

Aaaa, well, there is 2 of us here trying to sell it, and I did not know it had already been discussed. I have not been paid for it yet, So the fat lady hasn't sang yet. What else are you looking for, I can check my shed? Still Friends? Craig

Dang me, Wish I had a 1/2 dozen of these things to go around. Sorry I haven't posted on this seat. Been busy dealing with other seats, rims, air dams, and other stuff. But the Corbeau seat is spoken for at this time. If there should be a problem I will repost info. to continue. Thank you for everyones interest and help with this. Regards Craig.

Come to think of it, yea, it was bolted thru the stock seat mounts that are on the floor. It sits a little lower than stock, but the PO had to drill two new holes in the stock mount to install not thru the floor. Or do like I did and use a piece of Uni-strut U-rail to space between the stock mounts and the bottom of the seat. I remember it was a tight hand squeeze removing the bolts from the floor mounts. That is why I used Uni-strut channel to space 1.5" up from stock mounts and it made installtion easier. I mount the Uni-strut rail to the stock floor mounts then the seat to the rails. Of course I measured and pre-drilled all the holes then installed. Sorry, it was the safety harness eyebolts that went thru the floor, not the seat bolts. Anyhow, yes you would need to do some measuring and hole drilling to install. If you get the adapter slide rails from Corbeau the holes line up from stock holes to seat holes. Hey for $25 bucks, the seat is a steal, but there is some install work to do.

Seat is a fixed, not recline type but, I purchased adjustable track mounts from a Corbeau distributor when I got the new ones since we have 2 dirvers. This one was bolted up thru the floor or (onto track mounts) into the seat. The seat has threaded holes in the bottom and an anchor tab on the top area to attach to cage if you have one, or cut off tab. The seat is fiberglass inside so it is very light. I will look into shipping charges and let you know. Here is another front pic. Craig

Where you set your seat!

Here is the back. I don't know where the white specks came from in the pic. Must be the flash. It has 2 threaded holes under the seat and 1 center bracket on back near top.

Corbeau seat available for $25. I paid over $300 each for my new ones. This one is clean. There is some of the material pulling out from under the plastic seat belt trim around the left side belt hole. Otherwire no tears or stains. Here are some pics. First come first serve.:classic:

The original has a couple people already finalizing the sale. I will work up a photo of the Corbeau, it's a good seat. We just wanted to start new with matching his & her seats. Okay I posted the Corbeau for sale. Good Luck

I know, I refuse to grow up! My 3 kids claim to be more mature than I am. . .:stupid:

Nope, no Z-drivers seat. But I do have an older style Corbeau racing seat available if some one needs one for $25. I was thinking of mounting the PS2-playstation streering wheel & pedals to it and race in-doors.

and the tread on the other 2 tires. Both pairs are 195/60R15.