Zs-ondabrain

That looks like an electronic ignition but difinately not an XR3000 set-up. Where did you get the xr3000? was it new in the box, get it from a friend, what? As far as I know, the XR 3000 is a complete kit that comes with the Fireball coil, ignition box (w/connectors, labels and directions) and 1 Optical insert that replaces your current (points or electronic) set-up. I think you're missing something. Dave.

I can't even remember where I got those but I'm so glad I did. They've come ion handy more than once. Dave.

Good to hear you made it OK, me and leah wish you 3 the best. You can still chat with me here though. I finally got the 260Z in the garage and started tearing her down. The hood and fenders are at the scrap yard and the replacements are on the wall. Seems like most of the rust was on the panels, the metal under them was'nt too bad. I'll just use the SEM on some spots, prime it and move on. Keep in touch, Dave.

Hope this helps. Save them to your computer, it's easier that way. Dave 70_240z_wiring.pdf

Do you have this peice in your Dizzy? If you do, and it only has 2 wires, then something is seriously wrong or you got robbed. The picture shows the optical set-up inside a converted dizzy. Take a picture of the inside of your dizzy and the rest of your set-up, Dave.

The optical assembly that goes in the distributor has 3 wires and a molex, did you instal that into the dizzy? I too have a 260Z with the XR3000 set-up. Everything is labeled. The red, Yellow and black go to the coil..... Red to (+) on the coil. Yellow to the (-) on the coil and the black gets grounded. Then the black, white and grey wires on a molex go to the dizzy, the optical insert goes in the dizzy in place of the points. Then connect the dizzy to the molex. Dave.

Patience is the biggest rule of the game. We are older, kinder, gentler, MORE patient and deserving than your local honda kid. We deserve these cars because we have spent a lifetime dealing with cars that need too much work or not enough. When people see you driving down the road in your beautiful Classic ZCar, It's because YOU put it there, it's full of your blood, sweat and tears. If you break away now, you might as well be leaving your men while they're under fire, behind enemy lines. Stick with it, fix the little things, then go enjoy your car, knowing that it did'nt break you and your that much smarter and wiser than some kid in a fricken Honda. Keep the car, put in the work, enjoy the ride, Dave.

Finally took 3 days to sell off a bunch of wood working tools (huge drill press, Grizzly table saw, Ryobi router table and a B&D Radial arm saw) Cleaned everything up and built a few shelves, tossed a bunch of crap, gave away my 300ZX B/W T-5 tranny and 79' ZX 5-speed and a few other things and found enough room to slide the 260Z in the garage, FINALLY!! There's just no way in Hell that I'm leaving the 70' outside this winter when I start working on the 74'. I'll pull the 70 out on nice days when I got body work on the 260Z but other than that, it'll sit in a corner. As you can tell from the pictures, Anything that can fit on the wall is shelved, nailed and bolted to the wall and out of the way. Parts on one side and tools on the other. It's cramped but it works. Dave.

The is a page from MSA, it's good for starting out prices, also check your local Craigslist. I found the Urethane Air Dam that MSA sells for $199 for $30 just down the road from me. http://www.thezstore.com/page/TZS/CTGY/7AD2 Dave.

Just make sure that you regularly pull the linkage bars and clean out the cups and pivot balls with a Q-tip or rag, lightly grease them, pull thelinkage swival on the firewall and clean the shaft and bushings and regrease them as well. "A well oiled Machine" bla bla bla. Replace "oil" with grease and she'll be smooth as a babies butt. even regrease the pedal assembly while you're at it. and double check the strength of the return springs. Dave.

Adding the front air dam WILL give a more responsinve feel at higher speeds as well as give a little more down force on the front end. My 70' was wobbly as hell at high speeds until I installed the Urethane Air Dam. To correct the inward folding of the air dam at high speeds, I used 1/2" "L" bracket across the front of the lower lip then used the same style L bracket to Hold the lip outwards by screwing that bracket from the frame to the lower lip of the air dam. This basically helps it hold its shape and give the car down force without folding in. I can now hit an easy 130 MPH without wiggle or loss of steering control. I had already replaced all the rubber with urethane bushings and upgraded to KYB's and Eibach springs but the air dam definately finished it all off. Dave.

Isn't that what I kind of just wrote?? "1/4" steel plate, taller end links" Sounds like the same kinda deal. But what-ever works.

Nice thing about the Editgrid is I can update as I go without waiting and waiting like I do with Zhome. I just added the 260Z and updated the 240Z. Dave

Sounds like your end-links are too short. Get at least 1/2" taller end-links and if that don't work, Run a 1/4" steel spacer between the frame and the frame mounts. Are you noticing the "Touching" when the car is in the air or with the car on the ground? The lower the control arms, the higher the bar will sit near the oil pump. so if it's hitting while the weight of the car is on the wheels, you need longer end-links. Dave.

Everything around here is an Indian (North American Native) Name. Even Seattle was a Chief. Stillaguamish, Snohomish, Tacoma, Sammamish, Sequim (Pronounced Squim), Snoqualmie, Steilacoom, Spokane, Sumas and the list goes on. All Indian names I think.

Yup, he's there on the week-ends sometimes, but you'll never get him to answer the door. That's his Private time. Oliver's a good guy and definately knows his way around a Z. By the way, First Gen would be known as the S30 as they were the first Z cars until the body change in 79 thru 83. Series one would be the very first marketed design of the 240Z (69' to early 71') The Series 1 Z is recognized mainly by it's vented hatch (2 chrome horizontal vents) and 240Z emblem on the upper quarter panel behind the quarter window (Datsun circle with "240Z" written across the circle. My numbers may be off a little but there was only about 16,000 ?? series 1's. Series 2 Z's have vented quarter panel emblems and non vented hatches. There are Many differences between years but no matter what you get, you'll find everything you need to know about that speciofic year right here at CZCC (Classic Z Cars Club) I'm in Marysville, write me any time you're gonna be in the area, we'll shoot the shite and go from there. Welcome to the Best damn Z car site on the web. Dave.

I wish I had more time as well. I spend very little time on the actual "Working on the car" Hell, MY car would be farther along if I had more time. Thanks a lot man, Dave.

YUP, and I'll just add it the list of other uprades that I make on a day to day basis, all by "Thyself".

This is in no way, a "Sellable" item. This a "Do it Yourself" how to upgrade. You have to weld a rod into your hatch after grinding that lip. The most I could do is sell the actuator and a prebent rod but that would almost be pointless. you can use a hanger out of your closet for the rod and the actuator is available on-line. hopefully I did'nt make the write up too complicated sounding. It's pretty simple. The only hard part about it is getting something into thehole to grind that lip and getting your mig welder's tip into the hole to weld the rod in place. I ran the weld wire out of the tip about an inch to reach the farthest point. The tricky part is getting the rod to hold still and upright while welding it. And like they say, nothing worth doing, is easy. On a scale of 1 thru 10, 10 being the hardest to do, I give it 3. Fairly easy, some hard parts, but fairly easy and time consuming. Dave.

For years, I've read about people fiddling with a Hatch Release of one sort or another. Stuff from other cars, Inverting the lock to the boby and the catch bar to the hatch (I did this one) and even as far as running a release cable from the roof - thru the hatch frame and over to the lock. Anyways, I was discussing possible idea's with Stan, a friend of mine, and I came up with this one. Went down to the 260Z and went to work. I pulled the rear cover on the hatch, Latch assembly and the hatch lock. Took a 3/32" dia. rod and cut it at 1". Then gave it a slight bend in the center, about 30 degrees, then bent some 1/8" feet on the ends. then set it aside. Inside the latch hole, you'll see a 1/8" lip to the right or the square hole. Grind that lip flat so that the 1/16" cable (from the 11 lb Trunk release actuator) can slide where that lip is. I used an angle grinder with a 1" cutting wheel on it (started as a 3" disc but had used all but one inch of it) Slid the disk thru the hole and carefully ground the lip flush. Then I put the bent rod into the hole, lined it up parrellel with the ground down lip and welded it in place. Then I took the Latch and let it soak in some Carb Cleaner to remove the years of grease, dust and exhaust buildup. Cleaned it off and used white lithium grease on all the moving parts. Then I drilled a 5/64" hole in the latch handle with a really good drill bit, this is hardened steel and you'll need a good bit. Then I used a bigger bit to make a inset divet in the top so the cable will sit flush. Then I used a dremmel with a thin cutting wheel to make a slice in the latch handle so the cable could be slid thru the slice and into the hole (see the picture) Then I took the cable to the bench vice, clamped it in with 1/4" of cable exposed. grabbed the mig welder and ran the wire out about an inch, grounded the vice and welded a ball onto the end of the cable by tapping the cable with the weld wire, a ball would form on the wire then I'd tap the cable again till the ball welded to the cables top. Then used the grinder to smooth out the ball enough to fit in the divet of the latch handle and thru the bent rod. I ran the cable into the hatch area, thru the welded rod, and out the latch hole so I could slide the cable into the latch handle, thru the slice. Then I pulled the cable back into the hatch and installed the Latch back into the hatch and bolted it down. Keeping a slight tension on the cable, I pulled it over to the emblem side of the inner hatch area. I shaved 3/8" off the top of the actuator holder in order for it to fit in the hatch area, below the emblems. I slid the actuator into the holder and slid them into the hatch. with a slightly loose cable, I bolted the holder into place then tightened the screws of the holder into the actuator. The slack on the cable will give the actuator a slight head start and tug on the cable when you activate it to pop the hatch. I re-installed the lock and tried it. The sunken cable does not interfere at all with the operation of the lock and latch. Now drill a small hole into the frame of the hatch near the drivers side defrost cable. run single 16 gauge wire thru the hole, thru the frame and over to the actuator then plug it in. Ground the other lead of the actuator to the hatch using one of the bolts of the holder. Now run the wire from the defrost wire area to the dash area of the car and use a relay to power it. Relay diagram is below. here's a link to the hatch being popped video on youtube. Dave. Hatch release relay.bmp

Start checking the wiring around your Turn signal switch. The brake lights, turn signals and flasher wires go thru the T/S switch and associated wiring. also make sure that the Flasher unit is connected correctly, there is only 2 wires so it should be an easy swap and check. Check the wires of the Hazard switch, the body of that switch is fair game to gremlins.

That's nothing. Try bolting in a flywheel, bolting up the pressure plate, sliding the tranny in effortlessly, bolting the tranny up in place and letting the car down, then looking for the keys to start it up and finding the keys.........on top of the clutch. ARGGGGGG. That was a long day. Or how about bolting up the wheel, after a four point brake job, only to find the 2 new brake shoes on the bench. many more but not worth the embaresment. Dave.

I've got 16X7's with 225/50ZR16's on the 70' (shown below) but I'm thinking about going with a 225/45ZR17 for the 260Z. What's the best "Zero Clearance Issue" size to use with a 17" wheel? Anyone??

They are blowing out their current stock to make room for new stock and NEW items that came about during the summer. You'll also find that they do that after The Vegas shows like SEMA, when everyone comes out with new products. Dave.

It's cool, I just wanted to let him know that I understood what he did. Dave.