woof

Haha I’ve got a 10x1.25 tap somewhere too. I spent 30 minutes looking for it, could NOT find it. Went and bought a new tap and handle (couldn’t find the handle either. Moved things around to reach it better, and found the *real* problem. I had a new rack installed (old one was sloppy in the middle but solid on the outside, that’s now resolved). But the shop I took it to installed the ujoint one spline off, so the cutout on the shaft was sticking out into the bolts path, and stripped the bolt when it went in. I’ve called the shop, they are going to make it right.

Yep, threads are bad on the ujoint. Going to run a tap through it and see if I can save it.

Ah bugger. No wonder it didn't want to come out. I was thinking it was somehow captive. Turns out there IS a lock washer, I just couldn't see it. Hopefully the threads on the ujoint are ok.

hmm, I hadn't considered that it might be popping threads - I just thought it was turning out. I'll go pick up a new bolt (and washer!) and see what I can see.

I'm having an issue with the lower u-joint staying tight (steering column to rack). I really have to crank the bolt down that holds it to the rack. Once it's nice and tight, no steering slop. It's great for a few minutes but is coming loose after a few minutes of driving. It loosens enough that I have maybe 1/4" of play at the wheel. Crank it down again, and I’m fine for a few minutes. There's no split lock washer on it. What should I do here? Add a locking washer, put a jam nut on the other side, use some medium Loctite? Thanks!

Sharp looking setup.

Old thread, but since no one has responded. Techno Toy Tuning has brake upgrade kits. I did their ‘Micro big brake kit’ front and rear, and I’m quite happy with them. Pricey but very nice.

Z Car Depot has them - any experience with theirs? Oddly enough that’s what I was about to order.

Probably these https://www.dapperlighting.com/products/1970-1973-datsun-240z-advanced-sequential-led-tail-lights-jdm-spec-w-reverse?

Dapper Lighting has a pretty decent sale - 20 off.

Haha thanks for this! Will likely make an order with ZCD on Friday!

Installed a set of Retrobelts and a subwoofer. Also cleaned up a lot of wiring - wrapped everything I could get to in wire loom, and replaced a flimsy fuse block with a nice little Blue Sea. IMG_7255.mov

Got a baseline! The tech said that little dip just before 5k was pretty consistent, thought it might be electrical. Next step, EFI!

Changing the oil?

I had one on my 4runner for years until I sold it. Held up great. I usually put a hose on it when doing an oil change, made things very tidy. I was always nervous about snagging it on something and opening it up on the trail or it vibrating open (irrational I know). That never happened. I did have the little plastic safety snapped on, and zip tied in place. Can't be too careful :).

I assume I would need to pull the window, seals/gaskets, badges, etc before it goes into the dunk tank?

I've found some surface rust on the inside of my 240Z's hatch, mostly at the bottom. It seems that water was in there at some point, but I don't see any signs of recent ingress. Should I leave it alone, or spray the inside of the hatch with Rustoleum? Do something else?

I went to a Driver's Skills event hosted by the local Audi club. It was an absolute blast. I learned some new skills, and got to play with (and push) the Z with an instructor in the passenger seat. There were all kinds of cars there - lots of Audis and Porsches, a couple Toyota Tacomas, a 4Runner, and even a Subaru Forester. My Z was the oldest car there by some margin. Aside from a minor coolant leak (quickly solved by tightening up a hose clamp), no issues. HIGHLY recommended.

Just seeing this now. I already told somebody they can have 'em, not going to back out :). Looks like nice ones are worth some decent money, but these are far from perfect. I don't need to profit off them, and I'm happy to have them go to someone that will use them.

View Advert 240Z hubcaps Free! Save them from the recycler! I believe these to be the original hubcaps from my '71 240Z. I will never use them so I thought I'd see if someone here wants them. Pick up in Seattle or ship at recipient's expense. Advertiser woof Date 04/26/2024 Price $0.01 Category Parts for Sale  

I mounted a fire extinguisher! Oh, and I also replaced the *ancient* spare tire.

New member, first post! I fixed my windshield washers. Cleaned the reservoir, replaced the motor and all the lines, and cleaned the spray nozzles. It works now, for first time in 30+ years! In the process of yanking one of the old lines off, I stabbed myself with it. Who knew that 50 year old flexible tubing would harden enough to break skin!