sam280z

After you have the idle speed and balance set with the fast idle screw backed off, screw the fast idle screw in to raise the engine speed and use the balance screw to balance the rear to the front. You will probably have to move back and forth between the balance and fast idle screws to maintain a good engine speed for the off-idle balance. After they are balanced, back off the fast idle screw. It is just used for tuning.

That's an old Clifford Research system.

The correct thing to do would have been to stop the car and get it running before descending. Barring that, descending a little at a time allowing the brakes to cool at regular intervals. Using engine braking on a non-running carbureted engine is a good way to fill up the exhaust system with gasoline.

Kroil is the best penetrating oil I've used. I find it to be much better than PB Blaster which is much better than anything else. I've also heard of mixing equal parts ATF and acetone, but have not tried this myself. Alternate heat and cold. Tap harder than you think you should on the bolt with a ball peen hammer while you attempt to turn with the vice grips. Sometimes using impacts (hammer to vicegrips) versus steady turning will break it free.

Was it possibly over-reved? The head looks pretty clean. How old is the gas? Varnished gas can coat the valve stem and make the valve stick or close too slowly. Tis means that the rocker will lose contact with the cam and can bounce off of valve. The part on the left is a keeper. You will have to compress the valve spring while the valve is held closed to replace it. You can use compressed air supplied through the spark plug hole while that cylinder is on its compression stroke (both valves closed - cam lobes up) to do this. I use a hose from my compression tester. Another option is to put that cylinder's piston about half way up on the compression stroke, feed in a bunch of nylon twine through the spark plug hole (hang onto the end), then turn the engine to use the twine to hold the valve closed. The part n the right is the lash pad. The shiny spot makes it look like it may have been damaged. If it has been nicked there, you will have to replace it with one of equal thickness. Sam

I do not have that setup anymore. The picture is of the "stock" Mikuni system. Glad to have helped. Sam

The "stay holder" bolts to the cover of the last carb and holds the "terminal holder". You should be able to make one pretty easy using something like this: http://www.jegs.com/i/Mr-Gasket/720/3811G/10002/-1?parentProductId=763730 I have attached a pic of my old setup so you can see where everything bolts together.

"I am thinking of cutting my SU rod and mounting this bellcrank on it " This is what the Mikuni instructions call for. I've attached a scan of the instructions. Sam mikuni.pdf

You're over thinking this. Just pull the line off of the modulator and stick it into the seafoam. Engine vacuum will pull in the seafoam and it will get distributed evenly enough. YOu will want to kick up the engine speed. Sam

You can use DOT5 in a daily driver. I did for the past 10 years with no maintenance. Just pulled the brakes off of that car and the fluid looked brand new. One downside to DOT5 is if water gets in the system, it will pool in the lowest point, causing corrosion. Easy to prevent- don't get water in there. Another downside is a slightly softer pedal - DOT five is slightly compressible and entrains air very easily - don't shake the container. These two factors combine for a less than hard pedal feel. I put the fluid in a mason jar and use a mityvac to pull a vacuum on it before installing to get the entrained air out. I have never rebuilt a MC. Always replaced them. Sam

1: Get a can of kroil and spray all the flare nuts. 2: Get a name brand flare nut wrench so you don't round off the flare nuts. If they won't budge after treating with kroil, use a butane torch to heat them. This will save you from having to change the hard lines. 3: Plan on changing the flexible lines as well as the parts listed by Blue. If this is an occasional driver / show car consider using silicone (DOT5) fluid. It is not for racing but extends the life of seals and does not absorb water. If you go this route, you will want to flush the system with alcohol and compressed air. One thing to be careful of with the master cylinder, if you elect not to rebuild or replace, the act of bleeding the brakes can damage the seals if there is any corrosion inside the MC. This is because the piston will move past areas that it normally does not encounter. Sam

Brian, Are you sure the oil is coming from between the head and block? Often a valve cover leak will cause oil to accumulate at the head/block interface. There are only 2 tiny places where oil moves between the head and block. Usually a bad head gasket will seep water/lose compression. I would clean the engine very well and recheck for exactly where the oil is coming from before I attempted to change the head gasket. That being said, you need to purchase a manual - Haynes at a minimum - Factory Service is best. I also recommend the How to Rebuild. These have explicit instructions on how to do this. To answer you questions: Yes, You have to remove the sprocket to get the chain off. Yes, but not recommended without setting a TDC first and not without removing the sprocket. In a perfect world, if you put everything back exactly like it came apart, not important. In the real world, very important. Find TDC before you wedge the chain. Sam

Most likely cause is your brake booster diaphragm is leaking.

I'm curious about the ability to re-key Datsun door locks, especially 77-78 locks. At least the ones I have are assembled by crimping the chrome face plate over the tumbler when it slid in from the front. The only way to disassemble is to un-crimp the faceplate, and I don't know how you would do that without damaging it. Has anyone actually had their door locks re-keyed? Sam

If you were me, you'd do a leakdown test to start. It will tell you what's going on or at a minimum remove most possibilities. Sam