ollie Posted June 19, 2012 Share #25 Posted June 19, 2012 Hey Rainman, did you use closed cell foam for the top of the gas tank to protect against the body? Thanks! Link to comment https://www.classiczcars.com/topic/41992-assembling-early-260z/?page=3#findComment-393461 Share on other sites More sharing options...
Rainman Posted June 24, 2012 Author Share #26 Posted June 24, 2012 No Ollie, I used only the stock rubber "pucks" that were originally glued to the top of the tank. There was no closed cell foam on top of my tank when I dropped it out of the car the first time in 2006. Link to comment https://www.classiczcars.com/topic/41992-assembling-early-260z/?page=3#findComment-393916 Share on other sites More sharing options...
ollie Posted June 25, 2012 Share #27 Posted June 25, 2012 Thanks! Had I taken the time to actually go and look at the effort i put forth when I pulled the tank, I would have found that I carefully preserved 3 out of 4 of the pads from the top of the tank, not sure what happened to the 4th so I will use come closed cell foam for the last one. This weekend is the big push, hard lines, full braking system, fuel system and rear suspension are ready to be installed. Unfortunately I won't have my motor back until next week as the shop wants to dyno run it and we're msising the cam tower shims so I hope to have the car road ready by the end of July. I'm picking up my bumpers tomorrow from the plating shop as well, plating up here is like a black art and they charge accordingly....cheers, and I hope youre build is going well! Link to comment https://www.classiczcars.com/topic/41992-assembling-early-260z/?page=3#findComment-394014 Share on other sites More sharing options...
Rainman Posted June 26, 2012 Author Share #28 Posted June 26, 2012 Sounds like you're making great progress Ollie!! My progress is slow but sure.. I've been insulating the inside of the 260Z with HushMat. Finished it earlier this month before I left for work. It took 84 square feet to do it the way I wanted it done. Tried my best to waste as little as possible so it looks in places like a preschooler's art project.. But I didn't waste any.. Also cleaned up the engine and painted the block, need to do the same to the transmission before install. The trans was leaking a bit when it came out so will have to sort that out before it goes back together as well. I've got the Isis Power Master and Power Cells mounted and the harnesses labeled. You can see the Master Cell in the passengers foot well area. I'm looking forward to have a modern, programmable electrical system in the car. Won't get home again until late July so it'll be a while until I can work on it some more. The next step is putting in some of the interior pieces, specifically the windshield pillar covering so the windshield can be installed. The mechanicals and underside of the car will be done once the engine and transmission are installed. Need to find someone to recover my seats and door panels. Then it's all just glass and interior. Keep up the good work Ollie and watch for more updates around the beginning of August. Link to comment https://www.classiczcars.com/topic/41992-assembling-early-260z/?page=3#findComment-394091 Share on other sites More sharing options...
Fico Posted June 26, 2012 Share #29 Posted June 26, 2012 Looks great so far! how do you like that ISIS? Link to comment https://www.classiczcars.com/topic/41992-assembling-early-260z/?page=3#findComment-394107 Share on other sites More sharing options...
Rainman Posted June 26, 2012 Author Share #30 Posted June 26, 2012 (edited) Thanks Fico.. It's too early for me to tell with the Isis system but it seems like a great system. High quality components, detailed instructions and good customer support so far. Can't complain! Will keep you posted on the ease of installation as well as my impressions of the operation once it gets to that point. Seems nice and straight forward to me..How'd you get your cat to hold still with that bread around his noggin? I'd like to hear that story.. Edited June 26, 2012 by Rainman Link to comment https://www.classiczcars.com/topic/41992-assembling-early-260z/?page=3#findComment-394116 Share on other sites More sharing options...
Fico Posted June 26, 2012 Share #31 Posted June 26, 2012 Its about time a product like that came along, and they even say it right, most people can turn a wrench but give them a wire and they dont know what its for . Thats me to a "T". Ha ha i picked that picture up off the internet. Link to comment https://www.classiczcars.com/topic/41992-assembling-early-260z/?page=3#findComment-394128 Share on other sites More sharing options...
Rainman Posted June 27, 2012 Author Share #32 Posted June 27, 2012 I'm excited about the Isis Power system for two reasons.. First and foremost it will allow me to disable the ignition, making the car much harder for someone to steal. Second, it is completely programable and completely replaces all the old wiring. Last thing I want is for the old system to short out and catch fire after all this work.. I like your photo, it's hilarious! Link to comment https://www.classiczcars.com/topic/41992-assembling-early-260z/?page=3#findComment-394190 Share on other sites More sharing options...
Rainman Posted September 26, 2012 Author Share #33 Posted September 26, 2012 It's been a while since I've updated this thread, work on the 260 has been slow going to say the least.. I'm back at now so will get more photos posted with the activity. Enjoy.. Link to comment https://www.classiczcars.com/topic/41992-assembling-early-260z/?page=3#findComment-402662 Share on other sites More sharing options...
Rainman Posted October 9, 2012 Author Share #34 Posted October 9, 2012 Windshield installed yesterday... Check out the new headliner and vinyl as well.. Link to comment https://www.classiczcars.com/topic/41992-assembling-early-260z/?page=3#findComment-403811 Share on other sites More sharing options...
LeonV Posted October 9, 2012 Share #35 Posted October 9, 2012 Making great progress! Keep up the hard work, Tom! Link to comment https://www.classiczcars.com/topic/41992-assembling-early-260z/?page=3#findComment-403813 Share on other sites More sharing options...
justinyee Posted October 9, 2012 Share #36 Posted October 9, 2012 Wow - incredible job! Love watching this piece back together. Link to comment https://www.classiczcars.com/topic/41992-assembling-early-260z/?page=3#findComment-403825 Share on other sites More sharing options...
dspillman
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now