1972 Float Adjustment ...

[siteunseen]

I can't tell from that picture.  You should put a small ruler or pencil on the top of that boss on the float chamber then across to your clear tube to see if they are equal.

 

[siteunseen]

Is that sand on the bottom hose and all over the float chamber?  You may want to trade one of those fuel pumps for a belly pan.

Edited March 21, 2018 by siteunseen

[240260280]

4 hours ago, jalexquijano said:

You have not advised me on the level of the rear carb. Do i still need to bend the tang more?

 

 

Read this and you will be good. http://www.classiczcars.com/forums/topic/59745-definitive-70-71-240z-su-fuel-level-thread/

 

Edited March 21, 2018 by 240260280

[siteunseen]

He needs a timing light that shows rpm. May get a loaner from a chain store?

[siteunseen]

Another thing I thought of I don't remember mentioned is a fire extinguisher. Jalex you need a fire extinguisher.  The metel tipped Kidde fits perfect behind the passengers seat in that tool box. You need to move the spare tire tools behind the driver's seat tool compartment.

[Johnny wick]

I have a fire extinguisher since 3 years ago.

[psdenno]

27 minutes ago, siteunseen said:

He needs a timing light that shows rpm. May get a loaner from a chain store?

There's a nice one on Amazon for less than $80.  I may have to look into getting one of those, myself.  My 45 year old non-digital dwell tachometer is probably a bit out of calibration at this point.  Any brand recommendations?

Dennis

 

 

[siteunseen]

24 minutes ago, psdenno said:

There's a nice one on Amazon for less than $80.  I may have to look into getting one of those, myself.  My 45 year old non-digital dwell tachometer is probably a bit out of calibration at this point.  Any brand recommendations?

Dennis

 

 

Can't remember the name but it looks like an old flip phone. $100 red and blue backlight screen. amazon.com

https://www.amazon.com/INNOVA-5568-Pro-Timing-Light-Tool/dp/B000EVU8J8

It does it all. I like the dial back setting. I put it on 34 degrees rev it until 2,500 rpm and goes to zero.

[Johnny wick]

took the car for a ride yesterday and had to dial both fuel mixture knobs to 4 turns clockwise. 3 or 3.5 turns simply dont work. Could this be attributable to the fact that my engine is not stock and has been modified to 2.6Liters with a Schneider 274F camshaft and pertronix ignitor module and coil? I would really like to set it to 2.5 or 2.75 turns clockwise but it becomes to lean and lacks power.

I will test the car today without the airbox fastened to the carbs to ease the adjustments if necessary.

Edited March 22, 2018 by jalexquijano

[240260280]

Yes, fuel delivery requirement for a non-stock engine or non-stock needle on a stock engine will usually result in deviation from 2.5 turns.  As well engine issues may also require a deviation. 

[Johnny wick]

so 3.5 to 4 turns will be okay? in the past the former airtex 8012s fuel i had installed measured 4.2 psi and i could dial it at 2.75 to 3 turns clockwise. Maybe in the end the car does not need the 4.2 psi and will run okay with 3 psi but i will need to open the carbs more.

[psdenno]

You've been trying to adjust a modified engine to stock factory settings.  That can be like trying to fit a size 12 foot into a size 10 shoe.  The process of tuning the engine/carbs results in adjustments to settings to a point where it runs best.  Sounds like you're finally just about there.  Button that baby up and head out on the highway!

Dennis