Diseazd Posted October 28, 2017 Share #13 Posted October 28, 2017 Feels like a fan clutch to me. Had the same problem with my Stroker....new clutch was defective....put another clutch in.....works perfect. Link to comment https://www.classiczcars.com/topic/58783-overheating-after-modifications-what-am-i-overlooking/?page=2#findComment-533512 Share on other sites More sharing options...
Zed Head Posted October 28, 2017 Share #14 Posted October 28, 2017 My 76 has done the same thing in the past. It's either the fluid heating up and expanding or the water pump collapsing the lower hose, reducing overall system volume. The coolant reservoir level will only drop as the engine cools off and a vacuum is created in the coolant system, pulling coolant through the tube attached to the radiator neck. The radiator cap needs to be one designed to work with the reservoir, not an old 1950's cap. And it needs to be working correctly. If the radiator is full now you know there are no air pockets in it. Put the cap on and leave it. Make sure that the hose from the radiator fill neck to the reservoir is tightly sealed at both ends and has no pinholes, otherwise the system will suck in air instead of coolant from the reservoir as it cools down. Link to comment https://www.classiczcars.com/topic/58783-overheating-after-modifications-what-am-i-overlooking/?page=2#findComment-533513 Share on other sites More sharing options...
Chickenman Posted October 29, 2017 Share #15 Posted October 29, 2017 Jeremy. Is that the stock fan on the engine. Can you get a better picture of the fan. Something looks a little " Off " Link to comment https://www.classiczcars.com/topic/58783-overheating-after-modifications-what-am-i-overlooking/?page=2#findComment-533589 Share on other sites More sharing options...
grannyknot Posted October 29, 2017 Share #16 Posted October 29, 2017 (edited) If there is air trapped somewhere the best way I have found to purge it is start the engine cold and jack up the front end of the car with the rad cap off, make sure your interior heater valve is wide open. Usually burbs just after the T stat opens. Edited October 29, 2017 by grannyknot Link to comment https://www.classiczcars.com/topic/58783-overheating-after-modifications-what-am-i-overlooking/?page=2#findComment-533590 Share on other sites More sharing options...
Diseazd Posted October 29, 2017 Share #17 Posted October 29, 2017 Does the engine run normal when driving (moving) down the highway? Link to comment https://www.classiczcars.com/topic/58783-overheating-after-modifications-what-am-i-overlooking/?page=2#findComment-533592 Share on other sites More sharing options...
jeremy93ls Posted October 29, 2017 Author Share #18 Posted October 29, 2017 Thanks all for the help and suggestions. It's the stock fan. I cleaned/painted it bright white a while back. I'm unable to drive it on the road right now because it's not registered or insured yet. I'll get it out if I have to, but I'd really like to avoid it if possible. I agree, though. I'd love to know how it acts while driving instead of just idling in my backyard. The system did pull coolant back out of the reservoir bottle after it cooled down yesterday. The coolant was an inch or more over the MAX line when I shut it off. I should have raised the nose end up to purge out any air. I'll try that today. If it still gets too hot, I'll order another fan clutch. I remember buying the cheapest one ebay had a few years ago. Rock Auto has an AISIN unit for $36. Link to comment https://www.classiczcars.com/topic/58783-overheating-after-modifications-what-am-i-overlooking/?page=2#findComment-533593 Share on other sites More sharing options...
Diseazd Posted October 29, 2017 Share #19 Posted October 29, 2017 Just saying.....if it runs cool when moving, but overheats when at stop lights or just idling, it indicates that your air flow is adequate will moving, but not while idling (fan clutch). If it overheats while moving, you’ll need to look further. Link to comment https://www.classiczcars.com/topic/58783-overheating-after-modifications-what-am-i-overlooking/?page=2#findComment-533625 Share on other sites More sharing options...
Chickenman Posted October 30, 2017 Share #20 Posted October 30, 2017 On 10/29/2017 at 5:26 AM, jeremy93ls said: Thanks all for the help and suggestions. [Snip] It's the stock fan. I cleaned/painted it bright white a while back.[/Snip] Ah...it was the bright white paint that was throwing me off. Didn't look like a stock fan color. Link to comment https://www.classiczcars.com/topic/58783-overheating-after-modifications-what-am-i-overlooking/?page=2#findComment-533739 Share on other sites More sharing options...
jeremy93ls Posted November 4, 2017 Author Share #21 Posted November 4, 2017 I swapped in a new fan clutch this morning and topped off the coolant again, but it slowly climbed up to over 3/4 on the gauge. This time I had the front end raised a good bit. After it cooled down, I stuck a meat thermometer in the radiator neck and started it up. When I think the thermostat opened, it started spitting/splashing coolant out again. The thermometer showed about 140, but was still slowly climbing. Would an obstruction in the radiator cause this? Link to comment https://www.classiczcars.com/topic/58783-overheating-after-modifications-what-am-i-overlooking/?page=2#findComment-534122 Share on other sites More sharing options...
Zed Head Posted November 4, 2017 Share #22 Posted November 4, 2017 Could be. The top hose supplies the top "tank" of the radiator, from there the coolant has to flow through many small tubes to the bottom tank. The small tubes are what get clogged. Looks like you might have went past well-enough. Might not even be the thermostat opening, but if you wanted to test, you could remove the thermostat. Then you'll get immediate problems. On 10/22/2017 at 1:17 PM, jeremy93ls said: Pulled the radiator out, flushed the not-so-cruddy mixture out of it, then poured in a gallon of water with a measured bit of muratic acid and shook/rotated/flipped/worked the mixture throughout the radiator to hopefully clean the passages. Link to comment https://www.classiczcars.com/topic/58783-overheating-after-modifications-what-am-i-overlooking/?page=2#findComment-534123 Share on other sites More sharing options...
Reptoid Overlords Posted November 4, 2017 Share #23 Posted November 4, 2017 When it is hot, what happens when you squeeze the upper and lower radiator hoses(cap on)? Link to comment https://www.classiczcars.com/topic/58783-overheating-after-modifications-what-am-i-overlooking/?page=2#findComment-534124 Share on other sites More sharing options...
Zed Head Posted November 4, 2017 Share #24 Posted November 4, 2017 Here's another easy test of the radiator. Disconnect the hoses and fill the radiator from the top with a garden hose. You shouldn't be able to fill it faster than it runs out the bottom. If it overflows you'll know the cooling tubes are clogged. Link to comment https://www.classiczcars.com/topic/58783-overheating-after-modifications-what-am-i-overlooking/?page=2#findComment-534125 Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now